683161
57
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Split Operation
The same frequency is used for both reception and transmission
during normal communication. Select either VFO A or VFO B in
this case. However, depending on the circumstances, a different
frequency may be chosen for reception and transmission. In this
case, it is necessary to use two VFOs. This is known as split
operation. Split operation is used in cases such as when using
an FM repeater or when calling a DX station.
1
Press [SPLIT].
<< >> lights up when the transceiver enters the split
mode.
.
2
Press [A/B] to select “VFO A” or “VFO B”.
The value on the left is the RX frequency. (Indicated by
in the example)
The value on the right is the TX frequency. (Indicated by
in the example)
3
Select a frequency.
To copy a selected VFO frequency to the other VFO, press
and hold [A/B].
4
Press [A/B] to select the other VFO.
5
Select a frequency.
Exiting Split Operation
6
Press [SPLIT].
The transceiver switches to the simplex mode and the light for
<< >> goes off.
Direct Input of Frequency Difference Specified by DX Station
To directly configure the frequency difference between the
frequency specified by the DX station and the RX frequency,
perform the steps below while receiving signals from the DX
station.
1
Press and hold [SPLIT].
<< >> starts to blink.
2
Enter the frequency specified by the DX station in
units of kHz.
To exit the configuration process, press [CLR].
If the frequency specified by the DX station is a positive value, enter
the specified frequency in units of kHz using the numeric keypad.
If the frequency specified by the DX station is a negative value,
enter a “0” at the beginning of the frequency value.
For example, if “+5 kHz” is specified, enter “5”. If “-5 kHz” is
specified, enter “0” followed by “5”.
After input is complete, the TX frequency is configured and split
operation is now enabled.
<<
>> changes from a blinking to a solid display.
Turning the Tuning Control to Search for a TX Frequency
To search for a TX frequency by turning the Tuning control,
perform the steps below while receiving signals from the DX
station.
1
Press and hold [SPLIT].
<< >> starts to blink.
2
Turn the Tuning control to search for a TX frequency.
To exit the configuration process, press [CLR].
3
Press [SPLIT].
The frequency that is found in step 2 is configured as the TX
frequency and split operation is now enabled.
<<
>> changes from a blinking to a solid display.
F Display
This item displays the difference between the RX frequency and
TX frequency during split operation.
.
Configure in Menu [6-15] Delta Frequency Display
Setting Value Off/ On (default)
When the F display is ON, << >> is displayed below
the TX frequency display during split operation.
When <<
>> is displayed below the TX frequency, the
band memory number on the right will not be displayed.
When RIT or XIT is ON, the F value is the difference
between the TX frequency and the RX frequency with the
RIT or XIT frequency added.
Changing the split frequency using the [RIT/XIT]
control
While in the split mode with the RIT/XIT function set to OFF, the
split frequency can be adjusted by turning the [RIT/XIT] control.
Configure in Menu [3-12]
Split Frequency Offset by
RIT/XIT Control
Setting Value
Off (default)/ TX Frequency Offset while RX/ RX
Frequency Offset while TX/ Both
TX Frequency Offset while RX: Split transmission frequency
can be adjusted while receiving. While receiving signals from a
DX station, turning the [RIT/XIT] control changes the TX
frequency in advance to the frequency specified by the target
station.
RX Frequency Offset while TX: Split reception frequency can
be adjusted while transmitting. While one’s own station is
transmitting as a DX station, turning the [RIT/XIT] control
changes the RX frequency in advance to the frequency
specified for the target station.
Both: Enables both the above.
Adjustment of the split frequency using this function is
disabled during TF-SET.
COMMUNICATING AIDS 5
5 COMMUNICATING AIDS
5-1
57

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info