683161
59
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Switching the AGC Time Constant
1 Select a mode other than FM.
2 Press [AGC] to select an AGC time constant.
Pressing [AGC] each time switches the selection in the
following sequence: “AGC-F” → “AGC-M” → “AGC-S”.
.
Adjusting the AGC Time Constant Preset Value
1 Press and hold [AGC] to display the AGC
configuration screen.
.
2 Press F3 [AGC] or [AGC] to select “FAST”, “MID” or
“SLOW”.
3 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to change the AGC time constant.
Setting Value 1 to 20
The AGC time constant is fastest when it is configured to “1”,
and slowest when configured to “20”.
The default AGC time constant values in the respective
operation modes are as follows.
Mode
FAST MID SLOW
SSB 9 12 14
SSB-DATA 9 12 14
CW 9 12 14
FSK 7 11 14
PSK 7 11 14
AM 9 13 16
AM-DATA 9 13 16
4 Press and hold [AGC] or press [ESC] to end the
process.
AGC OFF
Turns off AGC according to the status of the signals received. RF
gain is fixed when AGC is set to OFF, which makes it easier to hear
weak signals in some cases.
If AGC is turned OFF while the S meter is deflecting due
to the signal, sound may be output to the speaker or
headphones at an unexpectedly loud volume.
Turn the [RF] control to turn down the RF gain level in advance.
After turning off AGC, adjust RF gain by turning the [RF] control
until the signal can be heard clearly.
To turn off AGC, perform the steps below.
1 Press and hold [AGC] to display the AGC
configuration screen.
2 Press and hold F6 [(OFF)] to configure AGC to OFF.
<< >> lights up and the preset value display area is
grayed out.
3 Press and hold [AGC] or press [ESC] to end the
process.
AGC Quick Recovery
This function performs recovery from the suppression that occurs
when the RX signal contains pulse noise.
1 Press and hold [AGC] to display the AGC
configuration screen.
2 Press F2 [PULSE] to display the AGC Quick
Recovery configuration screen.
.
3 Press F3 [ON/OFF] to set the function to “On”.
4 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to change the threshold level.
Configuring to a larger value activates this function when signal
level difference between the RX signal and pulse noise is small.
Setting Value
1 to 5 (default) to 10
This function may not be effective for pulse noise
occurring in short time interval.
Configuring to a value with a high threshold level may
cause the transceiver to malfunction and distort the RX
audio depending on the condition of the RX signal.
5 Press and hold [AGC] or press [ESC] to end the
process.
COMMUNICATING AIDS 5
5-3
59

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info