683161
55
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Drive Output (DRV)
The allowable output frequency ranges from the drive output
(DRV) are the 135 kHz band (135.700 kHz to 137.799 kHz), 475
kHz band (472.000 kHz to 478.999 kHz) and the amateur bands
between 1.9 and 50/70 MHz. The output impedance is 50 Ω and
output level is approximately 1 mW (0 dBm).
.
2
4
1
67
3
5
ALC Voltage
+12V
Control Voltage
TX
(Transmission)
Detection
Circuit
AMP
Linear Amplifier
(Typical Input at 1 mW)
Output Power at
Approx. 1 mw (0 dBm)
Connect Using a
Coaxial Cable
GND
ALC
LKY
DRV Connector
REMOTE Connector
(View from Rear Panel)
Turning ON/OFF Drive Output
Press [DRV].
Pressing [DRV] each time toggles drive output between ON
and OFF.
When drive output is ON, the [DRV] LED lights up in green.
During output from the DRV terminal, TX signals will not be
output from the ANT 1 and ANT 2 connectors.
Transmission from the DRV terminal will not be displayed on
the PWR meter. ALC (automatic level control) can be
operated by inputting ALC voltage from an external device
to the ALC terminal of the REMOTE connector. The
operating status will be displayed on the meter in this case.
The DRV output level is not controlled when there is no ALC
voltage input. As such, the output level is determined
according to the MIC input or [CAR] control settings.
Pay careful attention to the connection when making use
of drive output as described above.
Adjusting the Drive Output Level
Turn the [POWER] control.
nnn% is displayed according to the selected drive output
level. [nnn: 5 to 100]
A different drive output level can be configured for the AM
and modes other than the AM mode.
The resolution [1% / 5%] for changing the drive output level
can be switched using the Menu 6-04 “Transmit Power Step
Size” setting.
Band/Mode Setting Value
Default
HF
CW/FSK/PSK/SSB/FM/
SSB-DATA/FM-DATA
5 to 100 [%] (1 step or
multiples of 5)
100
AM/AM-DATA
5 to 25 [%] (1 step or
multiples of 5)
25
50M
CW/FSK/PSK/SSB/FM/
SSB-DATA/FM-DATA
5 to 100 [%] (1 step or
multiples of 5)
100
AM/AM-DATA
5 to 25 [%] (1 step or
multiples of 5)
25
70M
(E Type)
CW/FSK/PSK/SSB/FM/
SSB-DATA/FM-DATA
5 to 100 [%] (1 step or
multiples of 5)
100
AM/AM-DATA
5 to 25 [%] (1 step or
multiples of 5)
25
Built-in Antenna Tuner
It is important to ensure that the impedance of the coaxial cable
and that of the antenna coincide with each other. An external
antenna tuner or the built-in antenna tuner is used to adjust the
impedance between the antenna and this transceiver.
Impedance Matching with the Antenna
1 Select a TX frequency.
2 Press and hold F [ANT/PRE] to select an antenna.
When an external antenna tuner is connected to the ANT 1
connector, select ANT 2 if the built-in antenna tuner is to be
used.
The built-in antenna tuner cannot be used with ANT 1 when
it is connected to an external antenna tuner.
3 Press and hold [AT] to perform tuning.
The transceiver switches to the CW mode and starts tuning.
TX output power is automatically configured to 10 W and the
SWR meter will be selected as the TX meter.
<<
>> and [AT] LED will start to blink. << >>
blinks when the antenna tuner is ON during reception.
To undo the tuning, press [AT] again.
If the SWR (standing wave ratio) of the antenna is extremely
high (10:1 and above), an alarm tone (“SWR” in the Morse
code) will be output, and the built-in antenna tuner will be
disabled.
Adjust the antenna to lower the SWR before restarting the
tuning operation.
4 Check to ensure that tuning is complete.
When tuning is completed successfully, a Morse code tone
“T” is output.
When tuning is complete, the blinking << >> and
[AT] LED become lit in solid light. <<
>> blinks when the
antenna tuner is ON during reception.
If matching is not achieved for a duration of 20 seconds, an
alarm tone will be output (continuous output of “5” in the
Morse code). When this occurs, check the SWR meter and
press [AT] to stop tuning when the SWR value is low.
Tuning of the built-in antenna tuner will not be performed
outside the permitted TX frequency range.
During transmission, pressing and holding [AT] starts
the tuning.
If matching is not achieved for a duration of 60 seconds,
tuning will end automatically. When this occurs, the
antenna tuner circuit turns OFF, <<
>> will
disappear, and the [AT] LED will go off.
If tuning does not end automatically even though the
SWR of the antenna 3:1 or lower, adjust the antenna
system to lower the SWR and try to perform tuning again.
The SWR may not reach 1:1 even though tuning has
ended.
BASIC OPERATIONS 4
4-11
55

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info