782182
11
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
12 english
If necessary, correct as follows (Fig. 8.1):
Release the 4 hexagon bolts (2).1
Adjust the riving knife.2
Retighten the hexagon bolts (2).3
The riving knife is an important protective device for •
guiding the work piece and closing the gap behind
the sawblade, thus avoiding the kick-back of the work
piece. Mind the thickness of the riving knife – see the
embossed figures on the riving knife. The riving knife
must not be thinner than the sawblade and not thicker
than the width of the cutting gap.
Fig. 9
The riving knife must be in line with the sawblade. Correct
any difference as follows:
Release two hexagon bolts (1) each on both sides.1
Align the riving knife vertically.2
Slightly tighten the hexagon bolts (1).3
Adjust the riving knife in line with the sawblade, and 4
retighten the four hexagon bolts.
Check the clearance to the sawblade.5
Note:
If, at switching off, the brake lacks efficiency, it must be
examined by a specialist or replaced. A defective push
stick must be replaced.
Electrical connection
The installed electrical motor is connected ready to oper-
ate. The connection complies with the relevant VDE- and
DIN-regulations.
The power supply as well as the used extension cable
should comply with these regulations.
Motor-brake facility
Your construction circular saw is equipped with an auto-
matically functioning deadlock brake. The brake starts
functioning after switching off the motor.
Important information
The electrical motor is made for operating mode S 6 /
40 % .
When the motor gets overcharged, it automatically switch-
es off. After a short cool-down period (time varies) the
motor can be switched on again.
Defective electrical power supply cords
Electrical power supply cords often suffer insolation dam-
ages. Causes are:
Pressure spots, when power supply cords are being led •
through windows or doors.
Buckling spots by incorrect attachment or guidance of •
the power supply cords.
Cuttings by driving over a power supply cord. •
Insulation damages through pulling out of the socket. •
Cracks in worn-out insulation. •
Such defective electrical power supply cords should not
be used and are extremely dangerous because of the in-
sulation damage.
Check electrical power supply cords for damages on a reg-
ular basis. Please observe that upon checking the power
supply cord is not plugged in. Electrical power supply
cords have to comply with the relevant VDE - and DIN-
regulations. Only use power cables with the qualification
H 07 RN. An imprint of the type denomination is rule.
Alternating current motor, Page U5
The supply voltage should be 230 Volt/50 Hz.•
Extension cables must be up to 25 m long, have a cross •
cut of 1.5 square millimeter, be over 25 m long, and
have a minimum 2.5 square millimeter.
The powersupply should be 16 A.•
Rotary current motor
The power supply should be 400 Volt/50 Hz.•
The power supply and the extension cables must be •
5-fold leads = 3 P + N + SL.
Extension cables must have a minimum cable cross •
section of 1.5 square millimeter.
The power supply should be maximum 16 A.•
In case of connection to the power supply or moving •
site the rotary direction should be checked, otherwise
the polarity has to be changed (wall mounted connec-
tor).
Therefore screw the phase switcher into the plug sur-•
rounding with a screw driver. (See Fig. 10)
Connections and repairs of the electrical equipment should
only be carried out by an electrical specialist.
In case you have further questions, please specify the
following:
Motor manufacturer•
Current type of the motor•
Information of the machine type label•
Information of the switch type label•
When sending back the motor, always return the complete
power unit with switch.
Implementation
Please read the safety information before implementa-
tion.
The implementation of the machine is only admissable
when protection and safety facilites have been installed
completely.
Put the machine on a stable, even floor. If necessary at-
tach through the bottom through the holes to the frame
valves. (screws/nails)
After connection to the power supply your scheppach con-
struction circular saw is ready to operate.
Longitudinal cuts, Fig. 11
Use the fence for parallel cuts.•
For working smaller work pieces (less than 120 mm) •
use the push stick and the low fence side.
Attention: Do not use a defective or broken push stick •
or push handle any more (risk of injury).
A defective push stick and push handle must be •
replaced by new ones.
Immediately dispose of any defective parts.•
Cross cuts, Fig. 11.1
Use the cross-cutting gauge for cross and angle cuts.•
It is ready for use by lifting it onto the saw table.•
The setting scale reaches from 0° to 90°.•
In order to achieve a precise cut, press the wood against •
the fence surface when sawing.
When not used, lower the cross-cutting gauge at the •
side.
Wedge-cutting gauge, Fig. 11.2
The cross-cutting gauge is also used for cutting •
wedges.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Structo 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Structo 5 in de taal/talen: Duits, Engels, Frans, Italiaans, Pools, Fins als bijlage per email.

De handleiding is 9.22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info