782209
7
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
- 7 -
General view, KT 230 compound-type table (Fig. 2)
1. Handwheel for Xdirection (170 mm travel)
2.Scale ring
3.Work table (270 mm x 80 mm)
4. Table mounting hole
5. Pedestal
6.Handwheel for Ydirection (60 mm travel)
7.Support
8. Clamping screw
9. Scale
10.Pillar clamping screw
11. T-grooves
The PROXXON PF 230 milling machine may be used in
conjunction witha compound-type table or the PROXXON
PD 230/Elathe (in the latter case, the lathe support is used
in place of the compound-type table).
Technical data
PF 230 milling machine technical data
Voltage:115 Volt, 60Hz
Power rating:140 Watt
Short-term operation 10 min.
6 spindle revolutions by re-positioning the belt:
280,540, 780,910,1710 and 2500/rpm
Sleevestroke 30 mm (1 6 / 32”)
Verticaladjusting displacement200 mm (7 14/ 16 ”)
Generated noise70 dB(A)
Vibrations2.5 m/s2
Dimensions:refer toFig. 3
Weightapprox. 7.5 kg (16.5 lb)
Only for operation in closed rooms.
KT 230 compound-type table technical data
Workarea: 270 mm x 80 mm
Adjustment travel in Xdirection:170 mm
(10 5 / 8 x 3 5 / 32”)
Adjustment travel in Ydirection: 60 mm (2 3 / 8 ”)
Weight:9.5 kg (21 lb)
Dimensions of T-grooves: refer toFig. 4
Groove spacing: 25 mm (1”)
Feed per rotation:1.5 mm (1 / 16 ”)
Feed per graduation line: 0.05mm(3 / 64 ”)
Assembly of the milling machine
W arning:
Toavoid injury from unexpected starting or electrical shock,
do not plug the power cord intoapower source receptacle
during unpacking and assembly.This cord must remain
unplugged whenever you are working on the milling
machine.
W arning:
Ifany part is missing or damaged,do not plug the milling
machine in until the missing or damaged part is replaced,
and assembly is complete. Toavoid electrical shock, use
only identical replacement parts when servicing grounded
tools.
W arning:
For your safety,never connect the plug to the power source
receptacle until the assembly and adjustment steps are
completed, and you have readand understood the safety
and operating instructions.
Mounting on lathe PD 230/E
1. Mounting lathe on afirmbase.
2.Attach the mounting block 1 (Fig. 5) to the lathe 3, using
screws 2 (Do not tighten screws yet!)
3.Tighten screw 3 (Fig. 6)and insert pillar 1.
4. Tighten screw 4 toclamp the pillar.
5. Attach the milling table 3 (Fig. 7) to the lathe support
using screws 2 and square nuts 1.
Mounting of milling machine on KT 230 compound-type
table
Note:
Safe and precise operation is only possible if the machine is
properly fastened toa stable work surface.
1. Attachcompound-type table to work surface using 4
screws 1(i.e. M4,not included,look at Fig. 8).
2.Insert pillar in flange and clamp using screws 2.
W arning:
For your own safety,do not plug the tool into the power
source receptacle, until the parts arecorrectly installed and
adjustments havebeen made.
Impor tant!
Toavoid injury from accidental start,make sure the switch
is in the OFF position and the plug is not connected to the
power source receptacle beforechanging any parts or tools
(i. e. cutter)
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Proxxon FF 230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Proxxon FF 230 in de taal/talen: Engels als bijlage per email.

De handleiding is 1.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info