782209
8
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
-8-
Adjustment of the milling spindle
The milling spindle of the PF 230 canbe height-adjusted in
2 ways:
1. By using the fine feed 1 (Fig. 9)
2.By using the drilling lever 2
Verticaladjustment viafine tolerance feed
1. Loosen screw 3 (Fig. 9).
2.Adjust to the desired height using the hand wheel 1
(1 rotation corresponds to 1 mm feed).
3.Screw 3 must always be tightened again.
Feed via the drilling lever
1. Loosen screw 4(Fig. 9).
2.Loosen screw 6 and set scale 5 to zero.
3.Retighten screw 6.
4. Adjust to the desired height using the drill lever 2.
5. Retighten screw 4.
Note:
The drilling lever is not just used for height adjustment.It
canbealsobe used for drilling. Do not tighten the screw 4
when drilling.
Swivelling the milling spindle
The entire milling spindle canbe swivelled around twoaxes.
To swivel around the verticalaxis, release screw 4(Fig. 6)
and swivel the column completely into the required position.
Then retighten the screw.To swivel around the lateral
axis, release screw 1 (Fig. 10)and swivel the milling spindle.
Set the required number of degrees on the scale 2 and
retighten screw 1.
Assembly of the clamping devices for the milling machine:
Impor tant
Never insert the collet chuckalone into the spindle! Always
engage the collet chuck into the nut first!Always ensure
that collet chuckand milling tool have the correct diameter
for proper fit.
Please note:Further collet chuck dimensions areavailable
as accessory equipment in addition to thosecollet chucks
supplied. Theseare listed in our equipment catalogue.
Pleaseconsult our customer service department for further
information.
W arning:
Use only accessories recommended for this milling machi-
ne. Follow the instructions that accompany accessories.
Use of improper accessories may cause hazards!
1. Loosen union nut (7, see Fig. 1).
2.Place desired collet chuck 2:(see Fig. 11) into union nut
1and allow to engage.
3.Insert union nut withcollet chuck in the spindle and turn
sightly by hand.
4. Insert milling tool intocollet chuck.
5. Lock milling spindle using the spanners supplied and
tighten union nut.
6.To removecollet chuck loosen union nut and remove
milling tool.
7.Now remove union nut withcollet chuckcompletely from
milling spindle.
8. Disengage collet chuck using light sideways pressure 3
(Fig. 11) and remove from union nut.
Setting the spindle rotational speed
A total of 6 spindle speeds may beadjusted by shifting the
V-belt (Fig. 12 a/b): 280,540, 780,910,1710, and 2500
rpm.
Note:
Tighten belt only lightly!A belt installed too tightly places
excessive loads on the motor and machine mechanical
system!
1. Loosen knurled screw 4 (Fig.13)and open cover 7.
2.Loosen screw 5 using anAllen key by approx. 2 turns in
order to releasebelt pulley tension.
3.Placebothbelts in the desired position.
4. Press belt pulley 1 outwards with the belt tightener 8
below the gear wheels until the belt is tight.Tighten
screw 5.
5. Should bothbelts be tensioned unevenly, the upper belt
may be tensioned separately.To do so,loosen screw 2
and push motor 3 outwards until upper belt is tensioned.
6.Retighten screw 2.
Important:
The belt cover must always beclosed during operation.
Only tension the belts lightly.A too highly tensioned belt
strains the motor and the mechanics of the machine!
Replacement belts areavailable from the PROXXON central
service team (address on the rear side of these
instructions).
Working with the machine
Important:
The belt cover must always beclosed during operation.
Impor tant
Always wear protective goggles when milling. Take great
care to observe the safety regulations above.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Proxxon FF 230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Proxxon FF 230 in de taal/talen: Engels als bijlage per email.

De handleiding is 1.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info