782209
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
-9-
1. Securely fasten the work piece using clamps,in a vice,
or to the support of the lathe chuck. Alternatively, you
canclamp the work piece in amachine viceand mount
the vice on the work table using the T-grooves.
2.Adjust desired milling depth.
3.Tighten clamping screws 3 and 4 (Fig. 9).
4. Ensure that the milling tool does not touch the work
piece.
5. Ensure that the proper spindle speed has been adjusted.
6.Switch on milling machine at switch 3 (Fig. 1).
7.Work using a suitable feed
Note:
The feed must always take placeagainst the cutting
direction of the milling cutter (also refer Fig.14.)
Impor tant!
Always provide feed by hand only!When using the milling
machine in conjunction with the lathe PD 230/E, feed action
must not occur via the lathe's automaticfeed. Risk of injury!
Repair and maintenance
Impor tant:
Disconnect mains power beforecleaning and maintaining
unit.
Do not usecompressed air when cleaning.
Setting compound-type table guide play
If, after a time, the compound-type table guide is found to
have too much or too little play, the play canbe reset using
the adjusting screws 2 (Fig. 15). For this purpose,loosen
adjustment screw lock nuts 1and screw in all adjustment
screws evenly until play is eliminated. Retighten lock nuts
afterwards.
Setting compound-type table spindle play
If play of the spindles increases, release the nut 1 using a
socket spanner 2 or i. e. a ratchet. (Fig. 16)approx. one half
turn. Then turn the hand wheel to the right hand direction
until the play has been eliminated. Now retighten the nut 1
firmly, while holding the handwheel in the position it has
been adjusted.
Note:
See exploded view,page 10: Where necessary,play in the
individual spindle threads canalsobeachieved by slightly
tightening the spindle nut, Item 3, with the bolt, Item 25.
W arning
Toavoid fire or toxic reaction,never use gasoline,naphtha,
acetone,lacquer thinner,or similar highly volatile solvents to
clean the Milling machine.
Do not allow brake fluids,gasoline,or penetrating oils to
come in contact with the plasticparts.They contain
chemicals that can damage or destroy plastics.
Turn switchOFF and always remove plug from power
sourcebefore making any adjustments or repairs.
All electrical or mechanical repairs should be done only by
qualified service technicians.
When servicing use only PROXXON replacement parts.Use
of any other parts may createahazard or cause product
damage.
Any attempt to repair or replace electrical parts on this lathe
may createahazard unless repair is done by aqualified
service technician. Repair service is available at your
PROXXON servicecenter (You find the address at address
at the back of this manual)
Lubricating the machine
To ensurealong service life of your machine,please
observe the lubrication diagram in Fig. 17 (A: Lubricate
each time before use / B: Lubricate onceamonth). Only
useacid-free machine oil for lubrication.
Only useacid-free machine oil.
Replacement of the belts
Important:
Use only accessories recommended for this lathe. Follow
the instructions that accompany accessories.Use of
improper accessories may cause hazards.
If the belts become worn, you canchange them yourself.
Replacement belts areavailable from the PROXXON central
service team (address on the rear side of these
instructions).
•Unscrew screw 5 (Fig.13) to release the belt pulley 1.
•Unscrew the 3 screws 6 (Fig.13)and lift out the motor.
•You can now removeand replace the belts.
•Re-assemble in reverse order.
After use
Attention:
Disconnect milling machine mains plugbeforecleaning!
Cleancompound-type table and milling machine using a
soft clothand brushafter use. Then lightly oil the guides
and distribute the oil by moving the table. Never use
compressed air for cleaning the compound-type table as
cuttings entering the guides in this manner could destroy
the guides.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Proxxon FF 230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Proxxon FF 230 in de taal/talen: Engels als bijlage per email.

De handleiding is 1.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info