490654
18
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
18
into machine anti-clockwise operation.
In order to start the power tool, press the
switch [1-2]. The switch MAN/AUTO [1-4]
is in any position.
Use the switch [1-2] to gradually regulate
the speed.
CAUTION
If the forward / reverse switch [1-3]
is set to anti-clockwise operation, the
screwdriver can be started only by
pressing the switch [1-2] – without
additional pressure on the bit!
CAUTION
It is not necessary to remove the
depth stopper in order to unscrew
screws!
8.2 Depth stopper
Turning the depth stopper sets the screwing
depth – see gure [5]. The setting accuracy
is approx ± 0.1 mm.
Anti-clockwise rotation = screws are in-
serted deeper
Clockwise rotation = screws are in-
serted to lower
depth
Upon setting the depth, set some screws
to test and adjust the depth.
Depth stopper assembly
Fit the depth stopper [4-1] on the gear box
[4-5], until it engages in the groove.
Depth stopper disassembly
Remove the depth stopper from the gear
box by pulling it.
8.3 Hook and clip
Use the clip [6-1] to temporarily attach the
screwdriver on the working clothing – it can
be attached by means of a screw [6-2] to
the left or right of the power tool, and it is
suitable for right and left handed people –
see gure [6].
The screwdriver is equipped with a hook
[7-1], which is used for occasional machine
suspension. It can be attached to the left
or right of the power tool, by means of a
screw [7-2] – see gure [7].
8.4 Auto feed attachment
The auto feed attachment enables to work
continuously, without unnecessary delays.
Fitting the auto feed attachment
At rst remove the depth stopper [4-1], bit
holder [4-2] and bit, as speci ed in point 7.
Set the switch [1-4] into MAN position.
Push the long bit [8-1] completely to the
hexagonal spindle opening [4-4].
Then t the auto feed attachment on the
gear box. Push the attachment until it en-
gages in the groove of the gear box.
The attachment can be mounted at 30°
steps.
Removing the auto feed attachment
Use power to carefully pull the attachment
from the gear box.
Setting the screw length
Press button [9-1] to remove and insert the
depth stopper [9-2] and set the required
screw length. Read the set screw length on
the stopper sides [9-3].
Inserting collated screw strips
Pull the collated screws [10-3] through the
bottom guiding of the attachment, then
push the strip through the second guid-
ing until it engages in the working position.
Pull the belt slightly to make sure that it is
safely tted. Make sure that the rst screw
is in the screwing axes – see gure [10].
Use the wheel [10-1] to set the required
screwing depth. Turn to the right for in-
serting the screws deeper, and to the left
to screw to lower depth. The actual setting
position is visible on the presetting indica-
tor [10-2].
Upon setting, set some screws for test-
ing and use the wheel [10-1] to adjust the
depth, if required. Each setting change
complies with the stopper shift o ± 0.1 mm.
We recommend to screw in automatic
mode – see point 8.1 b).
Removing the collated screws
Pull upwards to remove the belt ( gure
[11]
) or press the transport lever and
concurrently pull the belt downwards ( g-
ure [11]
).
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Protool DWC 18-2500 DEC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Protool DWC 18-2500 DEC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 10,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info