512556
30
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
30
Diesel fuel flow sensor kit Installation and Operation Manual
NAVMAN
5
7
6
Install the required fittings to the straight
through pipe (for flare joints use a barrel union
fitting):
1 Apply thread sealer to the fitting’s ¼ NPT
threads.
Warning: Make sure pieces of the
threadseal tape or paste can not break
off and enter the fuel pipe (see section
7-2-5).
2 Screw each fitting in to the through pipe.
Use a spanner or wrench on the fitting and
another on the flats of the through pipe.
It does not matter which way round the through
pipe goes in the fuel line.
To attach a flare joint at the other end of the
sensor, repeat steps 3 and 4 above to bend
and cut the pipe, fit a flare nut and flare the
end of the pipe. Cut the pipe to length so the
flared end will meet the fittings on the sensor
port exactly. The exact amount you cut out will
depend on how much pipe length was used
up in the bends.
Otherwise, attach a different type of fitting
following the manufacturer’s instructions.
Hold the sensor in place and hand tighten the
fittings to check that the pipe lines up with the
sensor port and there is little strain on the joints.
Adjust the pipe bends so that the sensor will sit
flat against your chosen mounting surface.
Hold sensor in place
Put the flare nut on the pipe first!! Then flare
the end of the pipe using the flaring tool. Inspect
the inside face of the flared pipe - it must be
smooth and scratch-free. If it is not, cut the end
of the tube off and try again.
Put flare nut on first
4
Flare end of tube
Fit the straight through pipe. Tighten each fitting
with the correct tools (for a flare joint, use a
spanner or wrench on the flare nut and on the
barrel union). The fitting needs to be tight to
prevent leakage. Replace any pipe clamps that
you removed earlier.
Note: Leave the flare nut on the outlet side
of the install pipe loose now (see section 7-4,
step 5).
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Navman Diesel Fuel Flow Sensors bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Navman Diesel Fuel Flow Sensors in de taal/talen: Engels als bijlage per email.

De handleiding is 0,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Navman Diesel Fuel Flow Sensors

Navman Diesel Fuel Flow Sensors Gebruiksaanwijzing - Nederlands - 32 pagina's

Navman Diesel Fuel Flow Sensors Gebruiksaanwijzing - Deutsch - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info