512556
31
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
Diesel fuel flow sensor kit Installation and Operation Manual
31
NAVMAN
7-5 Test running and installing the sensors
This section describes how to test run the
engine and then install the flow sensors in place
of the straight through installation pipes:
1 When you have both supply and return
lines connected up and all fittings
tightened, bleed the fuel lines. This is the
same procedure you use after changing a
fuel filter - consult your engine manual.
2 Turn on the fuel tap at the tank. Run the
engine for 5 minutes. This will flush any
particles that you have introduced in the
installation process into the supply line
down to the secondary filter. Any particles
in the return line will be flushed back to
the tank. Check for pipe leaks.
3 Once you are happy with the pipework
changes, turn off the fuel tap at the tank.
4 Wear gloves to protect your hands from
the diesel fuel.
5 Put a tray of rags under the pipe where
you will disconnect it to absorb the fuel
that will spill.
6 Undo the fittings on the straight through
pipes and remove the straight through
pipes. Remove the ¼ NPT adaptors
from the ends of the install pipe. Clean
the thread sealer from the threads in the
install pipes and fittings.
Hand tighten the connections.
10 Screw the sensor to the mounting block
or support panel with the screws supplied.
11 Do up the fittings tightly with the correct
tool, except for the fitting on the outflow
side of the sensor in the supply line.
Leave this loose temporarily.
On flare nuts, use a spanner or wrench
on the flare nut, and another on the flats
of the barrel union. Flare nuts need to be
Tip: Keep the straight through pipes in a
safe place near to the sensors - you may
want them if you ever have to remove
the sensors, for service or to move the
system to another boat. If you have the
straight through pipe you can just put it in
the gap where the sensor came from, and
no re-work of the pipework is necessary.
7 Apply new threadseal to the ¼ NPT
adaptor threads (see section 7-5-2).
Warning: Make sure pieces of the
threadseal tape or paste can not break
off and enter the fuel pipe (see section
7-2-5).
8 Screw the adaptors into the real sensor.
Do not overtighten the adaptors - the
sensor body is diecast aluminium and
applying too much force when tightening
the adaptors will strip the threads.
9 Put the sensor in position:
Fit the sensor with the blue band in
the supply line.
Fit the sensor with the red band in the
return line.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Navman Diesel Fuel Flow Sensors bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Navman Diesel Fuel Flow Sensors in de taal/talen: Engels als bijlage per email.

De handleiding is 0,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Navman Diesel Fuel Flow Sensors

Navman Diesel Fuel Flow Sensors Gebruiksaanwijzing - Nederlands - 32 pagina's

Navman Diesel Fuel Flow Sensors Gebruiksaanwijzing - Deutsch - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info