448602
25
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
25
9. Groove cutting (Fig. 54)
A dado type cut can be made by proceeding as follows:
Adjust the lower limit position of the blade using the
adjusting screw and the stopper arm to limit the cutting
depth of the blade. Refer to “Stopper arm” section
described previously.
After adjusting the lower limit position of the blade, cut
parallel grooves across the width of the workpiece using
a slide (push) cut as shown in the figure. Then remove
the workpiece material between the grooves with a
chisel.
WARNING:
Do not attempt to perform this type of cut by using
a wider type blade or dado blade. Attempting to
make a groove cut with a wider blade or dado blade
could lead to unexpected cutting results and kickback
which may result in serious personal injury.
Be sure to return the stopper arm to the original
position when performing other than groove cut-
ting. Attempting to make cuts with the stopper arm in
the incorrect position could lead to unexpected cutting
results and kickback which may result in serious per-
sonal injury.
10. Special Max Width Cutting Capacities Technique
The maximum width cutting capacity of this tool can be
achieved by following the steps below:
For the maximum cutting width of this tool refer to the
SPECIFICATIONS under “Special Max Width Cutting
Capacities”
1) Set the tool at 0° or 45° miter angle and make sure
that the turn base is locked. (Refer to the section
titled “Adjusting the miter angle”.)
2) Remove both right and left upper fences temporarily
and set aside
3) Cut a platform to the dimensions indicated in the
drawing above using a 38 mm thick, flat stock mate-
rial such as wood, plywood or particle board.
WARNING:
Be sure to use flat stock as a platform. Stock that is
not flat may move during the cutting operation which
may result in kickback and serious personal injury.
NOTE:
The maximum cutting capacity in height will be reduced
by the same amount as the platform thickness.
4) Place the platform on the tool so that it extends
equally over each side of the tool base.
Secure the platform to the tool using four 6 mm
wood screws through four holes in the lower fences.
(Fig. 55)
WARNING:
Make sure that the platform is laying flat against
the tool base and secured firmly to the lower
fences using the four screw holes provided. Failure
to properly secure the platform may result in movement
and possible kickback resulting in serious personal
injury.
Ensure that the tool is firmly mounted to a stable
and flat surface. Failure to properly mount and secure
the tool could cause the tool to be unstable resulting in
a loss of control and/or the tool falling which may result
in serious personal injury.
5) Install both of the removed upper fences on the tool.
WARNING:
Do not use the tool without upper fences installed.
The upper fences provide the adequate support
required to cut the workpiece.
If the workpiece is not supported properly it may move
resulting in possible loss of control, kickback and seri-
ous personal injury.
6) Place the workpiece to be cut on the platform
secured to the tool.
7) Secure the workpiece firmly against the upper
fences with a vise before cutting.
8) Make a cut through the workpiece slowly according
to the operation titled “Slide (push) cutting (cutting
wide workpieces).(Fig. 56)
WARNING:
Ensure that the workpiece is secured with the vise
and make the cut slowly. Failure to properly secure
the workpiece and to cut slowly may cause the work-
piece to move resulting in possible kickback and seri-
ous personal injury.
Beware that after several cuts are performed at var-
ious miter angles the platform may become weak-
ened. If the platform becomes weakened due to the
multiple kerf cuts left in the material the platform should
be replaced. If the weakened platform is not replaced it
may cause the workpiece to move, during cutting,
resulting in possible kickback and serious personal
injury.
Carrying tool
Make sure that the tool is unplugged. Secure the blade at
0° bevel angle and the turn base at the full right miter
angle position. Secure the slide poles so that the lower
slide pole is locked in the position of the carriage fully
pulled to operator and the upper poles are locked in the
position of the carriage fully pushed forward to the guide
fence (refer to the section titled “Slide lock adjustment”.)
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. (Fig. 57)
WARNING:
Stopper pin is only for carrying and storage pur-
poses and should never be used for any cutting
operations. The use of the stopper pin for cutting oper-
ations may cause unexpected movement of the saw
blade resulting in kickback and serious personal injury.
Carry the tool by holding both sides of the tool base as
shown in the figure. If you remove the holders, dust bag,
etc., you can carry the tool more easily. (Fig. 58)
0° Miter angle: Over 450 mm (17-3/4”)
45° Miter angle: Over 325 mm (12-3/4”)
38 mm (1-1/2”)
Over 760 mm (30”)
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita LS 1216F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita LS 1216F in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 2,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info