448602
26
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
26
CAUTION:
Always secure all moving portions before carrying the
tool. If portions of the tool move or slide while being
carried loss of control or balance may occur resulting in
personal injury.
MAINTENANCE
WARNING:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance. Failure to unplug and switch off the
tool may result in accidental start up of the tool which
may result in serious personal injury.
Always be sure that the blade is sharp and clean for
the best and safest performance. Attempting a cut
with a dull and/or dirty blade may cause kickback and
result in a serious personal injury.
NOTICE:
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
1. Miter angle
Push the carriage toward the guide fence and tighten the
locking screw clockwise and pull the lock lever towards
the front of the saw to secure the carriage.
Turn the grip counterclockwise which secures the turn
base. Turn the turn base so that the pointer points to
on the miter scale. Then turn the turn base slightly clock-
wise and counterclockwise to seat the turn base in the 0°
miter notch. (Leave as it is if the pointer does not point to
0°.) Loosen the hex socket bolts securing the guide fence
using the socket wrench.
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Square the side of the
blade with the face of the guide fence using a triangular
rule, try-square, etc. Then securely tighten the hex
socket bolts on the guide fence in order starting from the
right side. (Fig. 59)
Make sure that the pointer points to 0° on the miter scale.
If the pointer does not point to 0°, loosen the screw which
secures the pointer and adjust the pointer so that it will
point to 0°. (Fig. 60)
2. Bevel angle
Push the latch lever forward fully to release the positive
stops.
1) 0° bevel angle
Push the carriage toward the guide fence and
tighten the locking screw clockwise and pull the lock
lever towards the front of the saw to secure the car-
riage. Lower the handle fully and lock it in the low-
ered position by pushing in the stopper pin. Loosen
the lever at the rear of the tool. (Fig. 61)
Turn the hex socket bolt on the right side of the arm
holder two or three revolutions counterclockwise to
tilt the blade to the right. (Fig. 62)
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule, try-
square, etc. by turning the hex socket bolt on the
right side of the arm holder clockwise. Then tighten
the lever securely. (Fig. 63)
Make sure that the pointers on the arm holder point
to 0° on the bevel scale on the arm. If they do not
point to 0°, loosen the screws which secure the
pointers and adjust them so that they will point to 0°.
(Fig. 64)
2) 45° bevel angle (Fig. 65)
Adjust the 45° bevel angle only after performing 0°
bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade to the left
fully. Make sure that the pointer on the arm holder
points to 45° on the bevel scale on the arm. If the
pointer does not point to 45°, turn the left 45° bevel
angle adjusting bolt on the side of the arm until the
pointer points to 45°.
To adjust right 45° bevel angle, perform the same
procedure described above.
Adjustment of the laser line position (Fig. 66 & 67)
For models LS1216L and LS1216FL only
WARNING:
Since the tool must be plugged in while adjusting
the laser line, special care must be taken to not
switch on the tool. Accidental start up of the tool may
result in serious personal injury.
CAUTION:
Never look directly into the laser beam. Direct eye
exposure to the beam could cause serious damage to
the eyes.
LASER RADIATION
Do not stare into beam.
NOTICE:
Beware that impacts to the tool may cause the laser
line to be misaligned or may cause damage to the
laser, shortening its life.
Adjusting the laser line for the left side of the blade.
1 Screw to change the movable range of the adjusting
screw
2 Adjusting screw
3 Hex wrench
4 Laser line
5 Saw blade
1
2
3
4
5
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita LS 1216F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita LS 1216F in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 2,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info