448602
24
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
24
Table (B)
Example:
In the case of cutting 52/38° type crown molding for position (1) in Fig. 47 & 48:
Tilt and secure bevel angle setting to 33.9° RIGHT.
Adjust and secure miter angle setting to 31.6° RIGHT.
Lay crown molding with its broad back (hidden) surface down on the turn base with its WALL CONTACT EDGE
against the guide fence on the saw.
The finished piece to be used will always be on the RIGHT side of the blade after the cut has been made.
Crown molding stoppers (optional accessories) allow easier cuts of crown molding without tilting the saw blade. Install
them on the base as shown in the figures. (Fig. 49 & 50)
Fig. 49: At right 45° miter angle
Fig. 50: At left 45° miter angle
Position crown molding with its WALL CONTACT EDGE against the guide fence and its CEILING CONTACT EDGE
against the crown molding stoppers as shown in the figure (Fig. 51). Adjust the crown molding stoppers according to
the size of the crown molding. Tighten the screws to secure the crown molding stoppers. Refer to the table (C) for the
miter angle.
Table (C)
7. Cutting aluminum extrusion
When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in Fig. 52 to prevent defor-
mation of the aluminum. Use a cutting lubricant when
cutting the aluminum extrusion to prevent build-up of the
aluminum material on the blade.
WARNING:
Never attempt to cut thick or round aluminum
extrusions. Thick or round aluminum extrusions can
be difficult to secure and may work loose during the
cutting operation which may result in loss of control and
serious personal injury.
8. Wood facing (Fig. 53)
Use of wood facing helps to assure splinter-free cuts in
workpieces. Attach a wood facing to the guide fence
using the holes in the guide fence and 6 mm screws.
See the figure concerning the dimensions for a sug-
gested wood facing.
CAUTION:
Use straight wood of even thickness as the wood fac-
ing.
In order to completely cut through workpieces with a
height of 102 mm to 120 mm a wood facing should be
used on the guide fence. The wood facing will space
the workpiece away from the fence allowing the blade
to complete a deeper cut.
Example:
When cutting workpieces 115 mm and 120 mm high, use
a wood facing with the following thickness.
WARNING:
Use screws to attach the wood facing to the guide
fence. The screws should be installed so that the
screw heads are below the surface of the wood fac-
ing so that they will not interfere with the position-
ing of the material being cut. Misalignment of the
material being cut can cause unexpected movement
during the cutting operation which may result in a loss
of control and serious personal injury.
NOTICE:
When the wood facing is attached, do not turn the turn
base with the handle lowered. The blade and/or the
wood facing will be damaged.
Molding position
in Fig. 47 & 48
Molding edge against guide fence Finished piece
For inside corner
(1)
Wall contact edge should be against
guide fence.
Finished piece will be on the Right
side of blade.
(2)
Ceiling contact edge should be
against guide fence.
For outside corner
(3)
Finished piece will be on the Left
side of blade.
(4)
Wall contact edge should be against
guide fence.
Molding position
in Fig. 47 & 48
Miter angle Finished piece
For inside corner
(1) Right 45° Save the right side of blade
(2)
Left 45°
Save the left side of blade
For outside corner
(3) Save the right side of blade
(4) Right 45° Save the left side of blade
Miter angle
Thickness of wood facing
115 mm 120 mm
35 mm 60 mm
Left and Right 45° 30 mm 45 mm
Left and Right 52° 25 mm 35 mm
Right 60° 25 mm 35 mm
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita LS 1216F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita LS 1216F in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 2,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info