448602
23
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
23
5. Compound cutting
Compound cutting is the process in which a bevel angle
is made at the same time in which a miter angle is being
cut on a workpiece. Compound cutting can be performed
at the angle shown in the table.
When performing compound cutting, refer to “Press cut-
ting”, “Slide cutting”, “Miter cutting” and “Bevel cut” expla-
nations.
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
miter saw with the moldings laid flat on the turn base.
There are two common types of crown moldings and one
type of cove moldings; 52/38° wall angle crown molding,
45° wall angle crown molding and 45° wall angle cove
molding. See illustrations. (Fig. 46)
There are crown and cove molding joints which are made
to fit “Inside” 90° corners ((1) and (2) in Fig. 47 & 48) and
“Outside” 90° corners ((3) and (4) in Fig. 47 & 48).
Measuring
Measure the wall length and adjust workpiece on table to cut wall contact edge to desired length. Always make sure
that cut workpiece length at the back of the workpiece is the same as wall length. Adjust cut length for angle of cut.
Always use several pieces for test cuts to check the saw angles.
When cutting crown and cove moldings, set the bevel angle and miter angle as indicated in the table (A) and position
the moldings on the top surface of the saw base as indicated in the table (B).
In the case of left bevel cut
Tabl e (A )
Tabl e (B )
Example:
In the case of cutting 52/38° type crown molding for position (1) in Fig. 47 & 48:
Tilt and secure bevel angle setting to 33.9° LEFT.
Adjust and secure miter angle setting to 31.6° RIGHT.
Lay crown molding with its broad back (hidden) surface down on the turn base with its CEILING CONTACT EDGE
against the guide fence on the saw.
The finished piece to be used will always be on the LEFT side of the blade after the cut has been made.
In the case of right bevel cut
Tabl e (A )
Miter angle Bevel angle
Left and Right 0° – 45° Left and Right 0° – 45°
Molding position
in Fig. 47 & 48
Bevel angle Miter angle
52/38° type 45° type 52/38° type 45° type
For inside corner
(1)
Left 33.9° Left 30°
Right 31.6° Right 35.3°
(2)
Left 31.6° Left 35.3°
For outside corner
(3)
(4) Right 31.6° Right 35.3°
Molding position
in Fig. 47 & 48
Molding edge against guide fence Finished piece
For inside corner
(1)
Ceiling contact edge should be
against guide fence.
Finished piece will be on the Left
side of blade.
(2)
Wall contact edge should be against
guide fence.
For outside corner
(3)
Finished piece will be on the Right
side of blade.
(4)
Ceiling contact edge should be
against guide fence.
Molding position
in Fig. 47 & 48
Bevel angle Miter angle
52/38° type 45° type 52/38° type 45° type
For inside corner
(1)
Right 33.9° Right 30°
Right 31.6° Right 35.3°
(2)
Left 31.6° Left 35.3°
For outside corner
(3)
(4) Right 31.6° Right 35.3°
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita LS 1216F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita LS 1216F in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 2,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info