691786
22
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
22 ENGLISH
Miter cutting
Refertothepreviouslycovered"Adjustingthemiter
angle".
Bevel cut
WARNING: After setting the blade for a bevel
cut, before operating the tool ensure that the saw
head and blade will have free travel throughout
the entire range of the intended cut. Interruption
of the saw head or blade travel during the cutting
operation may result in kickback and serious personal
injury.
WARNING: While making a bevel cut keep
hands out of the path of the blade. The angle of the
blade may confuse the operator as to the actual blade
path while cutting and contact with the blade will
resultinseriouspersonalinjury
WARNING: The blade should not be raised
until it has come to a complete stop. During a
bevel cut the piece cut off may come to rest against
the blade. If the blade is raised while it is rotating the
cut-offpiecemaybeejectedbythebladecausing
the material to fragment which may result in serious
personalinjury.
WARNING: Always remove sub-fence when
performing bevel cuts. Failure to do so may cause
seriousinjury.
►Fig.47
1. Loosen the lever and tilt the saw blade to set the
bevelangle(Refertothepreviouslycovered"Adjusting
thebevelangle").Besuretoretightentheleverrmlyto
secure the selected bevel angle safely.
2. Secure the workpiece with the vise.
3. Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
4. Gently lower the handle to the fully lowered posi-
tion while applying pressure in parallel with the blade to
cut the workpiece.
5. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
NOTICE: When pressing down the handle, apply
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.
Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle Bevel angle
Left and right 45° Left and right 0° - 45°
Right 52° Left 20° - Right 45°
Left 52° Left 45° - Right 20°
When performing compound cutting, refer to "Press
cutting", "Miter cutting" and "Bevel cut" explanations.
Cutting aluminum extrusion
►Fig.48: 1. Vise 2. Spacer block 3. Guide fence
4. Aluminum extrusion 5. Spacer block
When securing aluminum extrusions, use spacer blocks or pieces
ofscrapasshownintheguretopreventdeformationofthealu-
minum. Use a cutting lubricant when cutting the aluminum extru-
sion to prevent build-up of the aluminum material on the blade.
CAUTION:
Never attempt to cut thick or round
aluminum extrusions. Thick aluminum extrusions
may come loose during operation and round alumi-
numextrusionscannotbesecuredrmlywiththistool.
Cutting repetitive lengths
When cutting several pieces of stock to the same
length, ranging from 200 mm to 330 mm, use the set
plate (optional accessory). Install the set plate on the
holder(optionalaccessory)asshowninthegure.
►Fig.49: 1. Set plate 2. Holder 3. Screw
Align the cutting line on your workpiece with either the left
or right side of the groove in the kerf board, and while hold-
ingtheworkpiece,movethesetplateushagainsttheend
of the workpiece. Then secure the set plate with the screw.
When the set plate is not used, loosen the screw and
turn the set plate out of the way.
Carrying tool
WARNING:
Stopper pin is only for carrying and
storage purposes and should never be used for any
cutting operations. The use of the stopper pin for cutting
operations may cause unexpected movement of the saw
bladeresultinginkickbackandseriouspersonalinjury.
CAUTION: Always secure all moving portions
before carrying the tool. If portions of the tool move
while being carried loss of control or balance may
occurresultinginpersonalinjury.
1. Remove the battery cartridge.
2. Secure the blade at 0° bevel angle and the turn
base at the full right miter angle position.
►Fig.50: 1. Turn base
3. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
4. Carry the tool by holding the handle.
►Fig.51
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS600 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 32,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info