691786
23
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
23 ENGLISH
MAINTENANCE
WARNING: Always be sure that the blade is
sharp and clean for the best and safest perfor-
mance. Attempting a cut with a dull and /or dirty blade
may cause kickback and result in a serious personal
injury.
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Adjusting the cutting angle
Thistooliscarefullyadjustedandalignedatthefactory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle
1. Loosenthexingscrewcounterclockwise.
2. Rotate the turn base until the pointer indicates 0°
on the miter scale.
►Fig.52: 1. Fixing screw 2. Turn base 3. Miter scale
4. Pointer
3. Rotate the turn base slightly clockwise and coun-
terclockwise to seat the turn base in the 0° miter notch.
(Leave as it is if the pointer does not indicate 0°.)
4. Loosen the hex socket bolt securing the guide
fence using the hex wrench.
►Fig.53: 1. Guide fence 2. Hex socket bolt
►Fig.54: 1. Guide fence 2. Hex socket bolt
5. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
6. Adjusttheguidefenceuntilitmakesaperpendic-
ular angle with the blade using a triangular rule, try-
square, etc. Then securely tighten the hex socket bolt
on the guide fence.
►Fig.55: 1. Guide fence 2. Triangular rule 3. Saw
blade
7. Make sure that the pointer indicates 0° on the
miter scale. If the pointer does not indicate 0°, loosen
thescrewwhichsecuresthepointerandadjustthe
pointer so that it indicates 0°.
►Fig.56: 1. Screw 2. Miter scale 3. Pointer
Bevel angle
0° bevel angle
1. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
2. Loosen the lever at the rear of the tool.
3. Turnthe0°bevelangleadjustingboltontheright
side of the saw head two or three revolutions counter-
clockwise to tilt the blade to the right.
►Fig.57: 1.Adjustingbolt2. Lever
4. Turnthe0°bevelangleadjustingboltclockwise
carefully until the side of the blade makes a perpendic-
ular angle with the top surface of the turn base. Use the
triangular rule, try-square, etc. as a guide. Then tighten
the lever securely.
►Fig.58: 1. Triangular rule 2. Saw blade 3. Top sur-
face of turn table
5. Make sure that the pointer on the arm indicates 0°
on the bevel scale. If it does not indicate 0°, loosen the
screwwhichsecuresthepointerandadjustthepointer
so that it indicates 0°.
►Fig.59: 1. Screw 2. Pointer 3. Bevel scale
45° bevel angle
Adjustthe45°bevelangleonlyafterperforming0°
bevelangleadjustment.
1. Loosen the lever and tilt the blade to the left fully.
2. Make sure that the pointer on the arm indicates
45° on the bevel scale. If the pointer does not indicate
45°,turntheleft45°bevelangleadjustingboltonthe
right side of the arm until the pointer indicates 45°.
►Fig.60: 1.Right45°bevelangleadjustingbolt
2. Pointer 3.Left45°bevelangleadjusting
bolt
3. Tiltthebladetotherightfully,andthenadjustthe
right 45° bevel angle using the right 45° bevel angle
adjustingbolt.
►Fig.61: 1. Saw blade 2. Triangular rule
Adjusting the laser line position
WARNING: The battery cartridge must be
installed on the tool while adjusting the laser line.
Take extra care not to switch on the tool during
adjustment. Accidental start up of the tool may result
inseriouspersonalinjury.
CAUTION: Never look directly into the laser
beam. Direct eye exposure to the beam could cause
serious damage to your eyes.
NOTICE: Check the position of laser line regu-
larly for accuracy.
NOTICE: Beware that impacts to the tool. It may
cause the laser line to be misaligned or may cause
damage to the laser, shortening its life.
NOTICE: Have the tool repaired by a Makita
authorized service center for any failure on the
laser unit.
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS600 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 32,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info