691786
21
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
21 ENGLISH
CAUTION:
Make sure that the blade mounting part
"a" on the inner ange that is positioned outside ts
into the saw blade hole "a" perfectly. Mounting the blade
on the wrong side can result in the dangerous vibration.
Dust bag
The use of the dust bag makes cutting operations
cleaner and dust collection easier.
Toattachthedustbag,titontothedustnozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust bag of
its contents, tapping it lightly so as to remove particles adher-
ing to the insides which might hamper further collection.
►Fig.41: 1. Dust bag 2. Dust nozzle 3. Fastener
NOTE: If you connect a vacuum cleaner to your saw,
cleaner operations can be performed.
►Fig.42
Securing workpiece
WARNING: It is extremely important to always
secure the workpiece correctly with the vise.
Failuretodosomayresultinseriouspersonalinjury
and cause damage to the tool and/or the workpiece.
WARNING:
When cutting a workpiece that is
longer than the support base of the saw, the mate-
rial should be supported the entire length beyond
the support base and at the same height to keep the
material level. Proper workpiece support will help avoid
blade pinch and possible kickback which may result in
seriouspersonalinjury.Donotrelysolelyonthevertical
vise and/or horizontal vise to secure the workpiece. Thin
material tends to sag. Support workpiece over its entire
length to avoid blade pinch and possible KICKBACK.
►Fig.43: 1. Support 2. Turn base
Vertical vise
WARNING: Secure the workpiece rmly
against the turn base and guide fence with the
vise during all operations. Otherwise the material
may move during the cutting operation, cause dam-
age to the blade, and be thrown which may result in
lossofcontrolandseriouspersonalinjury.
Install the vertical vise on either the left or right side of the
guide fence. Insert the vise rod into the hole in the guide
fence and tighten the lower screw to secure the vise rod.
►Fig.44: 1. Vise arm 2. Vise knob 3. Guide fence
4. Turn base 5. Lower screw 6. Upper screw
7. Vise rod
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the upper screw. If the upper screw contacts
the guide fence, install the upper screw on the opposite
side of vise arm. Make sure that no part of the tool con-
tacts the vise when lowering the handle fully. If some
part contacts the vise, re-position the vise.
Presstheworkpieceatagainsttheguidefenceandthe
turn base. Position the workpiece at the desired cutting
positionandsecureitrmlybytighteningtheviseknob.
Attaching the shoulder strap
Optional accessory
CAUTION: Be sure to remove the shoulder
strap before operating the tool. The shoulder
strap may be entangled and cause injury.
CAUTION: Be sure to attach the hooks of the
shoulder strap to the tool securely. If the hooks
are attached incompletely, they may come off and
cause injury.
The shoulder strap is convenient for transporting the
tool. Attach the hooks of the shoulder strap to the tool
asshowninthegure.
►Fig.45: 1. Shoulder strap 2. Hook
OPERATION
WARNING: Make sure the blade is not con-
tacting the workpiece, etc. before the switch
is turned on. Turning the tool on with the blade in
contact with the workpiece may result in kickback and
seriouspersonalinjury.
WARNING: After a cutting operation, do not
raise the blade until it has come to a complete
stop. The raising of a coasting blade may result in
seriouspersonalinjuryanddamagetotheworkpiece.
NOTICE: Before use, be sure to release the
handle from the lowered position by pulling the
stopper pin.
NOTICE: Do not apply excessive pressure on the
handle when cutting. Too much force may result in
overloadofthemotorand/ordecreasedcuttingef-
ciency. Press down handle with only as much force as
necessaryforsmoothcuttingandwithoutsignicant
decrease in blade speed.
NOTICE: Gently press down the handle to per-
form the cut. If the handle is pressed down with force
or if lateral force is applied, the blade may vibrate and
leave a mark (saw mark) in the workpiece and the
precision of the cut may be impaired.
Press cutting (cutting small
workpieces)
►Fig.46
Workpieces up to 46 mm high and 92 mm wide can be
cut in the following manner.
1. Secure the workpiece with the vise.
2. Switch on the tool without the blade making any
contact and wait until the blade attains full speed before
lowering.
3. Gently lower the handle to the fully lowered posi-
tion to cut the workpiece.
4. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS600 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 32,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info