691786
20
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
20 ENGLISH
Aligning the laser line
Align the cutting line on your workpiece with the laser
line.
►Fig.31
A) When you want to obtain the correct size on the left side
of workpiece, shift the laser line to the left of the blade.
B) When you want to obtain the correct size on the right
side of workpiece, shift the laser line to the right of the
blade.
ASSEMBLY
WARNING: Always be sure that the tool is
switched off and the battery cartridge is removed
before working on the tool. Failure to switch off and
remove the battery cartridge may result in serious
personalinjury.
Hex wrench storage
Thehexwrenchisstoredasshowninthegure.When
the hex wrench is needed it can be pulled out of the
wrench holder.
After using the hex wrench it can be stored by returning
it to the wrench holder.
►Fig.32: 1. Wrench holder 2. Hex wrench
Installing or removing saw blade
WARNING: Always be sure that the tool is
switched off and the battery cartridge is removed
before installing or removing the blade. Accidental
start up of the tool may result in serious personal
injury.
CAUTION: Use only the Makita hex wrench
provided to install or remove the blade. Failure
todosomayresultinovertighteningorinsufcient
tightening of the hex socket bolt. This could cause
aninjury.
To remove the blade, perform the following steps:
1. Release the stopper pin, and then lock the handle
in the raised position by pushing in the stopper pin.
►Fig.33: 1. Stopper pin
2. Use the hex wrench to loosen the hex socket bolt
holding the center cover by turning it counterclockwise.
Then, raise the blade guard and center cover.
►Fig.34: 1. Center cover 2. Hex socket bolt 3. Hex
wrench 4. Blade guard
3. Press the shaft lock to lock the spindle and use
the hex wrench to loosen the hex socket bolt clockwise.
Then remove the hex socket bolt of the spindle, outer
angeandblade.
►Fig.35: 1. Shaft lock 2. Hex socket bolt 3. Outer
ange
4. Iftheinnerangeisremoved,installitonthespin-
dle with its blade mounting part facing the blade. If the
angeisinstalledincorrectlytheangewillrubagainst
the machine.
►Fig.36: 1.Outerange2. Saw blade 3.Innerange
4. Hex socket bolt (left-handed) 5. Spindle
6. Blade mounting part
To install the blade, perform the following steps:
1. Mountthebladecarefullyontotheinnerange.
Make sure that the direction of the arrow on the blade
matches the direction of the arrow on the blade case.
►Fig.37: 1. Saw blade 2. Arrow
2. Installtheouterangeandhexsocketbolt,and
then use the hex wrench to tighten the hex socket bolt
(left-handed) of the spindle securely counterclockwise
while pressing the shaft lock.
3. Return the blade guard and center cover to its
original position. Then tighten the hex socket bolt of the
center cover clockwise to secure the center cover.
4. Release the handle from the raised position by
pulling the stopper pin. Lower the handle to make sure
that the blade guard moves properly.
5. Make sure the shaft lock has released spindle
before making cut.
For tool with the inner ange for
15.88 mm hole-diameter saw blade
Country specic
Mounttheinnerangewithitsrecessedsidefacing
outward onto the mounting shaft and then place saw
blade(withtheringattachedifneeded),outerange
and hex bolt.
For tool without the ring
►Fig.38: 1.Outerange2. Saw blade 3.Innerange
4. Hex socket bolt (left-handed) 5. Spindle
For tool with the ring
►Fig.39: 1.Outerange2. Saw blade 3.Innerange
4. Hex socket bolt (left-handed) 5. Ring
6. Spindle
WARNING: If the ring is needed to mount the
blade onto the spindle, always be sure that the
correct ring for the blade's arbor hole you intend
to use is installed between the inner and the outer
anges. Use of the incorrect arbor hole ring may
result in the improper mounting of the blade causing
blade movement and severe vibration resulting in
possible loss of control during operation and in seri-
ouspersonalinjury.
For tool with the inner ange for
other than 20 mm or 15.88 mm hole-
diameter saw blade
Country specic
Theinnerangehasacertaindiameterofablade
mounting part on one side of it and a different diameter
of blade mounting part on the other side. Choose a
correctsideonwhichblademountingparttsintothe
saw blade hole perfectly.
►Fig.40: 1.Outerange2. Saw blade 3.Innerange
4. Hex socket bolt (left-handed) 5. Spindle
6. Blade mounting part
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS600 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 32,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info