691786
18
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
18 ENGLISH
2. Re-tighten them only to the extent that the kerf
boards can still be easily moved by hand.
3. Lower the handle fully and push in the stopper pin
to lock the handle in the lowered position.
4. Adjustthekerfboardssothatthekerfboardsjust
contact the sides of the blade teeth.
►Fig.13
►Fig.14: 1. Saw blade 2. Blade teeth 3. Kerf board
4. Left bevel cut 5. Straight cut
5. Tightenthescrews(donottightenrmly).
6.
Afteradjustingthekerfboards,releasethestopperpin
and raise the handle. Then tighten all the screws securely.
NOTICE: After setting the bevel angle ensure
that the kerf boards are adjusted properly. Correct
adjustmentofthekerfboardshelpstoprovideproper
support of the workpiece and minimizing workpiece
tear out.
Maintaining maximum cutting
capacity
Thistoolisfactoryadjustedtoprovidethemaximum
cutting capacity for a 165 mm saw blade.
When installing a new blade, always check the lower limit
positionoftheblade,andifnecessary,adjustitasfollows:
1. Remove the battery cartridge. Lower the handle
completely.
2. Usethehexwrenchtoturnthelowerlimitadjust-
ing bolt until the saw blade comes slightly below the
cross section of the guide fence and the top surface of
the turn base.
►Fig.15: 1.Adjustingbolt
►Fig.16: 1. Guide fence
3. Rotate the blade by hand while holding the handle
all the way down to be sure that the blade does not
contactanypartofthelowerbase.Re-adjustslightly,if
necessary.
WARNING: After installing a new blade and
with the battery cartridge removed, always be
sure that the blade does not contact any part of
the lower base when the handle is lowered com-
pletely. If a blade makes contact with the base it may
causekickbackandresultinseriouspersonalinjury.
►Fig.17
Sub-fence
Country specic
This tool is equipped with the sub-fence and small
sub-fences.
Sub-fence
WARNING: Always remove sub-fence when
performing bevel cuts. Failure to do so may cause
seriousinjury.
►Fig.18: 1. Sub-fence
When performing cuts except for bevel cuts, use the
sub-fence to support the workpiece.
Small sub-fence
CAUTION: When performing right bevel cuts,
fold the small sub-fences. Otherwise, they may
contact the blade or a part of the tool, and may result
inseriousinjurytotheoperator.
►Fig.19: 1. Small sub-fence 2. Scale
Whenperformingverticalcutorleftbevelcut,ipthem
upward to support the workpiece. The guide fence has
a scale of 10 mm interval.
Adjusting the miter angle
►Fig.20: 1. Fixing screw 2. Turn base 3. Miter scale
4. Pointer
1. Loosenthexingscrewcounterclockwise.
2. Adjusttheangleoftheturnbase.Usethepointer
and the miter scale as a guide.
3. Tightenthexingscrewclockwisermly.
CAUTION: After changing the miter angle,
always secure the turn base by tightening the
xing screw rmly.
NOTICE: When turning the turn base, be sure to
raise the handle fully.
Adjusting the bevel angle
Toadjustthebevelangle,turntheleverattherearof
the tool downward.
►Fig.21: 1. Lever
To tilt the blade to the left, hold the handle and tilt the saw
head. Use the bevel scale and the pointer as a guide.
Thenturntheleverupwardrmlytosecurethesawhead.
►Fig.22: 1. Pointer 2. Bevel scale
To tilt the blade to the right, hold the handle and tilt the
saw head to the left slightly, and push the release button.
With the release button pressed, tilt the saw blade to the
right.Turntheleverupwardrmlytosecurethesawhead.
►Fig.23: 1. Release button
CAUTION: After changing the bevel angle,
always secure the saw head by turning the lever
upward rmly.
NOTICE: When tilting the saw blade, be sure the
handle is fully raised.
NOTICE: When changing bevel angles, be
sure to position the kerf boards appropriately
as explained in the "Positioning kerf boards"
section.
Setting 46° bevel angle
1. Loosen the lever and tilt the blade to the left or
right fully.
►Fig.24: 1. Lever
2. To tilt the blade to the left, hold the handle and tilt
the saw head to the right slightly, and then move the
release lever to the direction of the arrow. The bevel
anglecanbeadjustedbetween45°to46°bytiltingthe
saw head while moving the release lever.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS600 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 32,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info