683161
184
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Symptom Probable Cause Corrective Action Refer to
The linear amplifier is not functioning. The REMOTE connector is not properly
connected.
Reconnect the connector properly.
16-13
The audio source selected in Data VOX is
different from the audio source input, or the
input level of the input signal is low.
Check the Data VOX settings or check the input
level of the input signal.
Control relay of the linear amplifier is turned off. Configure to a setting suitable for the linear
amplifier, such as “Active High + Relay Control”
for Keying Logic in the Linear Amplifier menu.
16-14
When a linear amplifier is used for full
break-in operation in the CW mode,
the SWR may deteriorate suddenly or
an abnormal ALC voltage may be
applied when the linear amplifier starts
up.
The linear amplifier in use requires some time
to start up (TL-922, etc.).
Operate in the semi break-in mode by
configuring to a setting that includes an
appropriate delay time for the linear amplifier,
such as “Active High + Relay Control” for
Keying Logic in the Linear Amplifier menu.
16-13
AT-300 is not functioning. It is connected to antenna input connector 2
(ANT 2).
Connect it to antenna input connector 1 (ANT
1).
4-12
The fuse inside this transceiver is blown. Check the fuse, address the cause and replace
the blown fuse with a new one.
17-4
Modulation is too shallow. (FM mode) Microphone gain is low. Configure the microphone gain in Advanced
Menu [10].
5-28
When a commercially available power
meter is used, the TX output power
reading for SSB is low compared to
the other modes.
The peak power of SSB is not correctly
measured.
To ensure correct measurement of the peak
power for SSB, the use of devices such as an
oscilloscope which are capable of displaying
instantaneous waveforms is recommended.
Commercially available power meters may not
be able to measure the peak power fully in some
cases. Please use them as reference values.
Transmission is still held after AT
tuning is complete.
TX hold after AT tuning is configured to ON. Configure TX hold after AT tuning to OFF in
Advanced Menu [7].
4-12
VFO scan does not start. Program Scan is selected. Configure all the settings for memory channels
P0 to P9 to OFF in the Program Scan/VFO Scan
configuration mode. Alternatively, press [VFO/
PRG] to select VFO Scan.
10-1
Memory Scan is not functioning. No data is registered in the memory channels. Register data to the memory channels. 9-2
Group Scan is not functioning. No data is registered in the memory channels
within the group.
Register data to the memory channels of the
corresponding group number.
10-3
All the memory channels within the group are
locked out.
Cancel the lockout for the memory channels to
be scanned.
10-4
Memory Scan is only performed on
specific channels.
Group Memory Scan is selected. Reconfigure or cancel the group selection.
10-3
Voice guidance does not start
automatically.
Auto voice guidance is OFF.
Configure auto voice guidance to On in Menu
[1-06].
13-1
Voice guidance is not output
automatically after Full Reset is
performed.
Menu [1-06] is configured to Off.
Turn on the power while pressing [PF A], or
configure Menu [1-06] to On.
13-1
The [POWER] LED is blinking and the
power of this transceiver does not turn
on.
This transceiver is preparing to activate the
program timer operation.
Wait for the program timer operation to start. To
stop the program timer operation, press [ ] for
4 seconds.
14-4
Program timer is not activated. The timer operation is not configured to ON. Check whether the timer operation has been
temporarily turned off (<< >> goes off) by
pressing F [TIMER] after the timer operation is
configured to ON.
14-4
A firmware version confirmation
screen is displayed and this
transceiver does not start up.
The firmware of this transceiver cannot be
detected.
Rewrite the firmware. If the same symptom
persists after rewriting the firmware, please
send an inquiry to KENWOOD service center
together with the number that is displayed at the
bottom right corner of the message.
17-1
Firmware cannot be updated. The name of the zip file is changed. Update the firmware without changing the
name of the zip file. The file name may be
changed if the file is downloaded to the PC
multiple times.
The zip file is uncompressed. Update the firmware without uncompressing
the zip file.
18 TROUBLESHOOTING
18-4
184

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info