683161
182
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Troubleshooting
Check the following before requesting for repair of the transceiver.
Problems Related to Reception and Transmission
Symptom Probable Cause Corrective Action Refer to
Power does not turn on when [ ] is
pressed.
The power switch of the regulated DC power
supply is not turned on.
Set the power switch to ON.
4-1
The DC power cable is not correctly connected. Check the DC power cable to ensure that the
polarity is correct. (Red: +, black: -)
1-1
The DC power cable is not fully inserted. Ensure that the cable is fully inserted. 1-1
The fuse of the DC power cable is blown. Address the cause of the blown fuse and
replace it with a new fuse according to the
designated capacity.
17-4
A voltage exceeding the 13.8 V DC ±15% range
is applied.
Check the output voltage of the regulated DC
power supply and configure it to the rated
voltage (DC 13.8 V).
1-1
The screen is not displayed normally
when this transceiver is powered on.
The microcomputer is malfunctioning. Reset this transceiver.
17-1
A backup data damage detected
screen is displayed.
The initialization data was not configured
correctly for some unknown reason.
Press F4 [OK] on the “backup data damage
detected screen” to perform Full Reset again.
Signals cannot be received even
when an antenna is connected.
The RX sensitivity is low.
The squelch is closed. Turn the [SQL] control and adjust accordingly. 4-2
The attenuator is ON. Set the attenuator to OFF. 6-1
The preamplifier is OFF. Set the preamplifier to ON. 5-6
The antenna 1/2 selection is wrong. Select the correct antenna. 4-10
RX ANT is ON. Check whether RX ANT is set to ON. 4-10
Unable to perform tuning even though the
antenna tuner is ON.
Press and hold [AT] to perform tuning.
Alternatively, stop the tuning operation.
4-11
The gain level is lowered using the [RF] control. Turn the [RF] control all the way to the right. 4-2
The transverter settings are not correctly
configured.
If the transverter is ON, check whether the
settings are correctly configured and whether it
is functioning properly.
16-15
The transverter is ON. If the transverter is ON, check whether it is
functioning properly.
16-15
Signals received are not correctly
demodulated.
The operating mode is incorrectly selected. Try switching to a different mode. 4-4
The AGC function settings are not correctly
configured.
Configure the AGC function settings correctly.
5-2
The frequency does not change when
the [RIT/XIT] control is turned.
The RIT/XIT function is OFF. Press [RIT] or [XIT].
5-7
The cutoff frequency of the RX audio
in the SSB mode is extremely high or
extremely low.
The RX DSP filter settings are not suitable for
operation.
Change them to the appropriate settings.
6-2
There is significant distortion in the
audio.
The AGC function is OFF. Set the AGC function to ON, or turn the [RF]
control to adjust RF gain.
5-2
The [AF] control is set to a loud volume level. Turn the [AF] control to adjust the volume. 4-2
No sound is output from the speaker. The [AF] control is turned all the way to the left. Turn the [AF] control to the right. 4-2
The [SQL] control is turned all the way to the
right.
Turn the [SQL] control to the left.
4-2
Headphones are connected. Unplug the headphones. 1-2
CTCSS is set to ON in the FM mode. Set CTCSS to OFF. 5-30
The S meter deflection is small in the
FM mode.
The S meter sensitivity level is low.
Configure the S meter sensitivity to High in
Menu [0-07].
4-10
“SCP.OVF” is displayed on the
bandscope.
The bandscope is receiving excessive signal. Use the attenuator for the bandscope.
7-1
18 TROUBLESHOOTING
18-2
182

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info