683161
185
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Problems Related to Data Communication, PC and Network
Symptom Probable Cause Corrective Action Refer to
Errors and retries occur frequently
during transmission in the DATA
mode.
The audio output level of the auxiliary
equipment is too high and modulation signals
are distorted as a result.
Lower the output of the auxiliary equipment
such that the ALC zone is not exceeded.
The audio input sensitivity of the data
communication terminal on this transceiver
does not match the input signal.
Adjust the audio input sensitivity of the data
communication terminal in menus [7-06] (USB)
and [7-07] (ACC 2) such that the ALC zone is
not exceeded.
16-7
High-frequency signal sneaks in and causes
distortion of the modulation signals.
a. The auxiliary equipment uses the same
regulated DC power supply as this transceiver.
b. The antenna SWR is high.
c. High-frequency signal from the antenna is
induced by this transceiver.
d. High-frequency signal sneaks in due to the
high audio input sensitivity of the ACC 2
connector.
Introduce measures to prevent high-frequency
signal from sneaking in.
a. Use a different power supply for the auxiliary
equipment and this transceiver.
b. Perform antenna matching again.
c. Try changing the earth of the antenna, this
transceiver and the auxiliary equipment.
d. Lower the audio input sensitivity of the ACC
2 connector in Menu [7-07].
16-7
Audio input to the data communication
terminal is not transmitted.
The audio source input path setting does not
match the terminal in use.
Press and hold [DATA] to configure the settings
on the DATA mode audio source input screen.
8-1
The method of transmission is not appropriate.
Transmit signals using one of the following
methods.
a. Transmit by controlling the PKS terminal of
the ACC 2 connector.
b. Transmit using the [PF] key configured for the
DATA SEND function.
c. Transmit using the “TX1;” PC command.
1-7
16-2
1-4
16-5
The level of the audio input to the data
communication terminal is low.
Raise the audio output level of the connected
auxiliary equipment, or raise the audio input
level of the terminal in use in menus [7-06]
(USB) and [7-07] (ACC 2).
16-7
Errors occur frequently during
reception in the DATA mode.
Decoding cannot be performed as the audio
output level of the data communication terminal
on this transceiver does not match the input
level of the auxiliary equipment.
Adjust the audio output level of the terminal in
use in menus [7-08] (USB) and [7-09] (ACC 2).
16-7
There is multi-path distortion or fading at short
intervals. (The RX signal strength is not
necessarily the best when it is strongest.)
When using a beam antenna, change the
orientation of the antenna to look for a position
that is less likely to cause errors.
Unable to communicate with
ARCP-890 or ARHP-890 using the
COM port.
The baud rates do not match each other. Check the baud rate of the TS-890S and
ARCP-890.
16-5
The COM port is unable to handle CTS/RTS.
Configure Advanced Menu [16] PSQ/PKS Pin
Assignment (COM Connector) so that the
COM port can handle CTS/RTS.
16-8
Unable to communicate with
ARCP-890 or ARHP-890 using the
USB port.
The driver is not installed on the PC. Download the driver from our website and
install it on the PC.
16-5
The correct driver is not installed on the PC
because the PC is connected to this transceiver
before the driver is installed.
Reinstall the driver.
16-5
The baud rates do not match each other. Check the baud rate of the TS-890S and
ARCP-890.
16-5
Flow control is not configured.
The COM ports of PC and ARCP/ARHP are
not matching.
Check that Advanced Menu [17] Virtual
Standard COM Port - RTS is configured to
“Flow Control”.
Check that the COM port number assigned
by the Device Manager of the OS for
communication between this transceiver and
ARCP/ARHP is the same as the number
specified by ARCP/ARHP.
(ARCP/ARHP uses the Standard COM port
number displayed in the Device Manager of the
OS.)
1-5
16-12
TROUBLESHOOTING 18
18-5
185

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info