683161
104
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Audio Scope
The TX/RX audio can be displayed on an “audio scope screen”
where a spectrum scope and an oscilloscope are displayed as well
as on a “multi scope screen” where a reduced display of the
bandscope appears at the top together with the “audio scope
screen”.
Displaying the Audio Scope
Press and hold [SCP] to display the Audio Scope
screen.
Pressing and holding [SCP] each time toggles the display
between “Audio Scope” and “Bandscope”.
Audio Scope Screen
Left: Spectrum scope
Right: Oscilloscope
.
Switching the Audio Scope Display Type
1 Display the Audio Scope screen.
2 Press [SCP].
Pressing [SCP] each time switches the selection in the
following sequence.
“Audio Scope screen”
“Multi Scope screen”
No scope display (ends scope display)
Multi Scope Screen
Top: Reduced bandscope display
Left: Spectrum scope
Right: Oscilloscope
.
3 Press [ESC] to end the display.
Switching the Spectrum Scope Attenuator
By switching the attenuator for the spectrum scope, the spectrum
display can be adjusted to a level that is easy to see.
Press F2 [ATT].
Pressing F2 [ATT] each time switches the attenuator.
Setting Value Off (default)/ 10 dB/ 20 dB/ 30 dB
Pressing and holding F2 [ATT] each time switches the
options in the reverse sequence.
The current setting is displayed at the top of the spectrum
scope.
Switching the Display Frequency Span of the
Spectrum Scope
The display frequency span of the spectrum scope can be
configured to 3 kHz or 8 kHz. Configure the display frequency span
to an appropriate setting according to the filter band setting and
frequency to observe.
Press F3 [SPAN].
Pressing F3 [SPAN] each time toggles the span between “3
kHz (default)” and “8 kHz”.
.
Display when 8 kHz is selectedDisplay when 3 kHz is selected
Switching the Oscilloscope Level
By switching the vertical level of the oscilloscope, the amplitude of
the waveform can be adjusted to a size that is easy to see.
Press F6 [LEVEL].
Pressing F6 [LEVEL] each time switches the level.
Setting Value 0 dB (default)/ -10 dB/ -20 dB/ -30 dB
Pressing and holding F6 [LEVEL] each time switches the
options in the reverse sequence.
The current setting is displayed at the top of the oscilloscope.
Switching the Sweep Time
Switching the sweep time of the oscilloscope alters the time range
of the oscilloscope display. The sweep time can be adjusted
according to the status of the signal to be observed.
Press F5 [TIME].
Pressing F5 [TIME] each time switches the sweep time.
Setting Value
1 ms/ Div/ 3 ms/ Div/ 10 ms/ Div/ 30 ms/ Div/ 100
ms/ Div (default)/ 300 ms/ Div
Pressing and holding F5 [TIME] each time switches the
options in the reverse sequence.
The sweep time is displayed at the bottom of the
oscilloscope.
Pausing the Audio Scope
When the waveform displayed on the Audio Scope screen is
paused, the waveform is maintained until it is unpaused. The audio
scope can be paused to enable analysis of the waveform without
being interrupted whenever the display is refreshed.
Press F4 [PAUSE] to pause the waveform display.
When the waveform display is paused, << >> is
displayed and both the spectrum scope on the left and the
oscilloscope on the right stop refreshing temporarily.
Pressing F4 [PAUSE] again cancels the paused state.
.
7 SCOPE FUNCTIONS
7-8
104

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info