683161
103
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Deleting a Registered Frequency
1
Press F2 [ ]/ F3 [ ] or turn the [MULTI/CH]
control to select the frequency to delete.
2 Press and hold F5 [(DELETE)] to delete.
Turning ON/OFF Marker Function
1 Press [MENU].
2 Press F [F.MKR].
If F [F.MKR] is not displayed, press F [MORE] to display F
[F.MKR].
Pressing F [F.MKR] each time toggles the marker function
between ON and OFF.
Displaying the Maximum Value in the Waveform
The maximum value of the waveform shown on the spectrum
scope screen can be displayed to get a better grasp of the signal
status.
Turning ON/OFF Maximum Value Display
Press F1 [MORE] followed by F7 [MAX.HLD].
Pressing F7 [MAX.HLD] each time toggles the maximum value
display between ON and OFF.
Configuring the Hold Type
Select the method of displaying the maximum value of the waveform.
Configure in Menu [8-02] Bandscope Maximum Hold
Setting Value
10 [s] (default)/ Continuous
10 [s]: Maximum value information is cleared after 10 seconds.
Continuous: Maximum value information is not cleared.
The maximum value information is cleared automatically
if the range of the span displayed changes regardless of
whether “10 [s]” or “Continuous” is selected.
Pausing the Waveform Display
The waveform display on the bandscope screen can be paused.
Press F7 [PAUSE] to pause the waveform display.
When the waveform display is paused, << >> is
displayed on the screen.
.
Pressing F7 [PAUSE] again cancels the paused state.
Averaging of Spectrum Scope Waveform
Averaging the waveform on the spectrum scope smoothens the
changes in the waveform display making it easier to observe the
intermittent signals.
Press F1 [MORE], then press F6 [AVE.] to switch the
averaging level.
Pressing F6 [AVE.] each time switches the selection in the
following sequence: “Off” (averaging disabled) → “1”
(minimum) → “2” → “3” (maximum) → “Off”. The averaging
level selected is displayed at the top right corner of the grid.
Pressing and holding F6 [AVE.] each time switches the
options in the reverse sequence.
The averaging level can be configured separately for audio
mode (SSB/AM/FM (including DATA mode)) and non-audio
mode (CW/FSK/PSK).
The default settings of the audio mode and non-audio mode
are “2” and “1” respectively.
Displaying the TX Signal Waveform
A waveform for the TX signal can be displayed when a bandscope
for transmission is displayed in the Center mode.
Configure in Menu [8-00] Bandscope Display
during TX
Setting Value Off (default)/ On
On: Displays the TX waveform in the bandscope while
transmission is in progress.
Off: Does not display the waveform in the bandscope while
transmission is in progress.
The setting for this function cannot be switched while
transmission is in progress.
SCOPE FUNCTIONS 7
7-7
103

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info