683161
89
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Configuring the Behavior of the HI/SHIFT and LO/
WIDTH Controls (SSB/SSB-DATA Only)
The high cutoff/low cutoff selection in the SSB mode and Shift/
Width selection in the SSB-DATA mode are preconfigured in the
default setting, but they can be changed in the menu.
SSB Mode
Configure in Menu [6-11] Filter Control in SSB
Mode (High/Low and Shift/Width)
Setting Value High & Low Cut (default)/ Shift & Width
SSB-DATA Mode
Configure in Menu [6-12] Filter Control in SSB-
DATA Mode (High/Low and Shift/Width)
Setting Value High & Low Cut/ Shift & Width (default)
Changing the Cutoff Frequency
In the SSB, AM and FM modes, the passband width of the filter
can be altered by changing the cutoff frequency (low or high).
The passband width can be changed so that the interfering signal
falls outside the bandwidth of the filter.
.
5 KHz2 KHz600 Hz0 Hz
Interfering Signal
Target Signal
Interfering
Signal
High Cutoff Frequency Range
Low Cutoff Frequency Range
1 Press the mode key to select LSB, USB, FM or AM
mode.
2 Press and hold [IF FIL] to display the RX Filter
screen.
3 Turn the [HI/SHIFT] or [LO/WIDTH] control.
Turning the [HI/SHIFT] control to the right increases the
cutoff frequency (high) while turning the control to the left
decreases the frequency.
Turning the [LO/WIDTH] control to the right increases the
cutoff frequency (low) while turning the control to the left
decreases the frequency.
The amount of change and the filter shape are displayed on
the filter scope and RX Filter screen.
.
4 Press and hold [IF FIL] or press [ESC] to end the
process.
Mode
Low Cutoff Frequency
(Hz)
High Cutoff Frequency
(Hz)
Setting Value Setting Value
SSB/ SSB-
DATA
0/ 50/ 100 to 200 (default)
to 2000 (100-step)
600 to 2800 (default) to
3000 (100-step)/ 3400/
4000/ 5000
AM/ AM-
DATA
0/ 100 (default)/ 200/ 300
2000 to 3000 (100-step)/
3500/ 4000/ 5000 (default)
FM/ FM-
DATA
0/ 50/ 100 to 200 (default)
to 1000 (100-step)
1000 to 2800 (default) to
3000 (100-step)/ 3400/
4000/ 5000
When configured to “Auto”, a roofing filter with a
bandwidth wider than the passband width of the DSP
filter is selected using high cutoff/low cutoff or Width/
Shift.
When “Auto” is configured in the AM mode, a 6 kHz
roofing filter is automatically selected if the high cutoff
frequency is 3 kHz or lower, and a 15 kHz roofing filter is
selected if the high cutoff frequency is higher than 3 kHz.
In the FM mode, the option is fixed at 15 kHz and cannot
be changed.
When the low cutoff frequency is increased until it
reaches the high cutoff frequency, the high cutoff
frequency will also change at the same time while
keeping the passband width at 0 Hz.
When the high cutoff frequency is decreased until it
reaches the low cutoff frequency, the low cutoff
frequency will also change at the same time while
keeping the passband width at 0 Hz.
REJECTING INTERFERENCE 6
6-3
89

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info