683161
91
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Preset Passband Characteristics
The frequently-used filter settings (high cutoff, low cutoff and
WIDTH/SHIFT) can be preset according to the style in which this
transceiver is used.
1 Press and hold [IF FIL] to display the RX Filter
screen.
.
2 Press [IF FIL] or F2 [FILTER] to select an RX filter.
3 Press F6 [FIL SET].
The current filter settings (high cutoff, low cutoff and WIDTH/
SHIFT) are stored as the preset values.
When preset values are applied, the values will be
highlighted in the display for approximately 0.5 seconds.
Pressing F7 [FIL CLR] restores the passband width
changed using the [HI/SHIFT] and [LO/WIDTH] controls to
the preset value.
4 Press and hold F [IF FIL] or press [ESC] to end the
process.
Audio Peak Filter in the CW Mode
During reception in the CW mode, if the signal intelligibility
deteriorates due to noise or other reasons, allowing the RX signal
to pass through the bandwidth with the pitch frequency as the
center frequency helps to improve the intelligibility of the RX signal.
Turning ON/OFF Audio Peak Filter
1 Select CW mode.
2 Press F [APF].
Pressing F [APF] each time toggles the audio peak filter of
the selected band between ON and OFF.
When audio peak filter is on, “ON” is displayed on the key
guide. “OFF” is displayed when the audio peak filter is turned
off.
.
Switching the Passband Characteristics
3 types frequency passbands are available for selection for the
audio peak filter.
1 Select CW mode.
2 Press and hold F [APF] to display the audio peak
filter (APF) screen.
.
3
Press F2[ ]/ F3[ ] to select a passband width.
Setting Value
Wide (320Hz)/ Medium (160Hz) (default)/
Narrow (80Hz)
4 Press and hold F [APF] or press [ESC] to end the
process.
Shifting the Passband Width
Shifting the passband width of the audio peak filter helps to avoid
interference with nearby frequencies.
1 Select CW mode.
2 Press and hold F [APF] to display the audio peak
filter (APF) screen.
.
3
Press F2[ ]/ F3[ ] to select the passband
width to be shifted.
4
Press F4[ SHIFT] or F5[SHIFT ], or turn the
[MULTI/CH] control to shift the passband width.
Setting Value -200 to 0 (default) to +200 [Hz] (5-step)
The shift amount of the passband width is ±200 Hz with the
pitch frequency as the center frequency.
The selected passband width for the audio peak filter shifts
from the pitch frequency toward a higher or lower bandwidth.
5 Press and hold F [APF] or press [ESC] to end the
process.
REJECTING INTERFERENCE 6
6-5
91

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info