683161
87
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Attenuator
The attenuator is a function for attenuating the RX signals. If there
is interference due to strong signals near the target signal, turning
on the attenuator helps to reduce interference caused by nearby
frequencies.
It is also effective in situations where the RX audio is distorted
when the RX signal is too strong. This transceiver comes with three
different types of attenuators.
Press F [ATT].
Pressing F [ATT] each time switches the attenuation level.
Setting Value Off (default)/ 6 dB/ 12 dB/ 18 dB
Pressing and holding F [ATT] each time switches the options
in the reverse sequence.
The attenuation level is stored for each antenna selection
band.
The status of the attenuator (attenuation level) is displayed
in the key guide.
.
Switching the RX Filter Band Characteristics
Switching the RX Filter (A, B, C)
The setting for the band characteristics of the RX filter on this
transceiver can be switched at one touch according to the
operating status to one of the three types (A, B or C).
The band characteristics are configured by combining the
roofing filter or IF and AF filter, high cutoff/low cutoff and WIDTH/
SHIFT. A different RX filter setting (A, B or C) can be stored for
each of the SSB, CW, FSK, PSK, FM and AM modes.
Press [IF FIL].
Pressing [IF FIL] each time switches the RX filter in the order
of “A”, “B” and “C”.
The selected filter is displayed at the top left of the filter
scope.
The RX filter does not switch to Type C if Menu [6-10] RX
Filter Numbers below is configured to “2”.
Configuring the Selectable Types of RX Filters
The selectable types of RX filters can be configured to three (A, B
and C) or two (A and B).
Configure in Menu [6-10] RX Filter Numbers
Setting Value
2/ 3 (default)
Filter Scope
The following information is displayed on the filter scope screen.
Selected RX filter (A, B or C)
Image of the RX filter passband characteristics (trapezoid)
Audio spectrum of the RX audio
Parameters including the IF filter passband width
Pitch frequency in the CW mode
Notch point of the notch filter
Passband width of the roofing filter
.
SSB
AM/FM
PSK
FSK
CW
The audio spectrum is not shown on the filter scope while
the audio scope screen is displayed.
The audio spectrum is not shown on the filter scope while
the RTTY/PSK communication screen is displayed.
An out-of-range marker
is displayed when the
image of the passband cannot be displayed within the
display area because the shift amount of the filter in the
CW mode is large.
The audio spectrum is usually displayed within the image
of the passband. However, it may be displayed beyond
the image of the passband if there are excessively high
input signals.
When the notch filter is ON, the indicator representing
the notch point is displayed in white. The indicator is
displayed in white when the notch point is on the positive
side of the carrier wave in the AM mode. If the notch point
moves towards the minus side of the carrier wave, the
indicator changes to orange and moves from the left
edge of the screen to the right edge.
REJECTING INTERFERENCE 6
6 REJECTING INTERFERENCE
6-1
87

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info