683161
85
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Operation in Narrow FM Mode
It is possible to switch to a narrow bandwidth during operation in
the FM mode. The occupied bandwidth and maximum modulation
factor are shown in the table below. Selecting FM Narrow
according to the modulation factor of the target station helps to
avoid distortion and deterioration in the clarity of the RX audio.
Mode Occupied Bandwidth
Maximum Modulation
Factor
FM (Wide) 16 kHz or lower ±5 kHz or lower
FM Narrow 10 kHz or lower ±2.5 kHz or lower
Press and hold [FM/AM].
Pressing and holding [FM/AM] each time switches between
“FM” and “FMN (Narrow)”.
.
Operating the FM Repeater
Switching this transceiver to split operation and turning on the tone
signal while in the FM mode enables this transceiver to be used in
the repeater operation mode.
.
88.5 Hz
29.520 MHz
29.620 MHz
29.620 MHz
88.5 Hz
29.520 MHz
Configuring the Tone Signal
Registering the tone settings to a memory channel and
calling up the frequency or operation information from
the memory channel eliminates the need to configure the
tone frequency each time. For more details on the
memory channel settings, please refer to “MEMORY
CHANNELS” (9-1).
The tone frequency may vary depending on the country
or region this transceiver is being used.
Selecting a Tone
Press F4 [TONE] to select “TONE”.
Pressing F4 [TONE] each time toggles the tone signal selection
in the following sequence: “TONE” → “CTCSS (CT)” →
“CROSS” → Blank (deselected).
.
Configuring the Tone Frequency
1 Press and hold F4 [TONE] while “TONE” is selected
to display the FM Tone Frequency screen.
.
2 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to select the tone frequency.
Tone Frequency (Hz)
67.0 88.5 114.8 151.4 177.3 203.5 250.3
69.3 91.5 118.8 156.7 179.9 206.5 254.1
71.9 94.8 123.0 159.8 183.5 210.7 1750
74.4 97.4 127.3 162.2 186.2 218.1
77.0 100.0 131.8 165.5 189.9 225.7
79.7 103.5 136.5 167.9 192.8 229.1
82.5 107.2 141.3 171.3 196.6 233.6
85.4 110.9 146.2 173.8 199.5 241.8
The default setting is “88.5 Hz”.
To restore the default setting, press and hold F1
[(RESET)].
3 Press [ESC] to end the process.
Tone Frequency Scan
Tone frequency that is contained in signals received in the FM
mode can be searched and displayed with the following steps. This
is useful when there is a need to know the tone frequency of the
repeater station.
1 Press and hold F4 [TONE] while “TONE” is selected
to display the FM Tone Frequency screen.
2 Press F7 [SCAN] to start tone frequency scan.
Scanning stops when a tone frequency is detected, and the
frequency is displayed in the “FREQ. [Hz]” field.
Pressing F7 [SCAN] while tone frequency scan is in
progress stops the scan operation. Pressing F7 [SCAN]
again resume scanning.
The scan operation stops when the RX signal is interrupted
during tone frequency scan. Scanning resumes when a RX
signal is detected by this transceiver.
3 Press [ESC] to end the process.
COMMUNICATING AIDS 5
5-29
85

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info