778530
29
Verklein
Vergroot
Pagina terug
1/185
Pagina verder
8.2 Acoustic warning signal
Acoustic warning signals sound and the ma
chine switches off in the following operating
states:
peep
Battery flat or machine
overloaded:
Change the battery
Reduce the machine load
8.3 Kickback stop function
WARNING
Risk of injury
The kickback stop does not guarantee com
plete protection against a kickback.
Always concentrate on your work and refer
to the safety instructions and warnings.
A kickback while working may cause the saw to
lift unintentionally.
The feeler wedge [8-1] detects unintentional
lifting (kickback) of the saw from the workpiece
or a rail during work and triggers the quick-act
ing braking of the saw blade (Fig. 8a).
This reduces the risk of a kickback. However, it
cannot be entirely ruled out.
KickbackStop function status LED
Colour Meaning
Green The KickbackStop function is ac
tive.
Orange The KickbackStop function is deac
tivated.
Flashing
orange The KickbackStop function is not
active.
The saw was started up before the
feeler wedge was pressed against
the workpiece or a guide rail. The
saw's plate is not positioned such
that it is completely level.
Once the saw has been positioned
such that is completely level, the
LED will switch to green. If this is
not the case, check the Kickback
Stop function (see Section 8.7)
Flashing
red The KickbackStop function has
been triggered.
8.4 Unintentional triggering of the kickback
stop function
Working without a guide rail on an uneven
workpiece may cause the kickback stop func
tion to trigger unintentionally (Fig. 8b).
The feeler wedge [8-1] runs along the work
piece. If there is a recess in the workpiece, the
position of the feeler wedge will correspond to
the position when the workpiece or guide rail is
lifted. This triggers the kickback stop function.
It may then be necessary to work without the
kickback stop function (see Section 8.6).
8.5 Procedure after the kickback stop
function has been triggered
Triggered by unintentional lifting (kickback)
Determine and eliminate any reasons for
lifting.
Check the machine for any damage.
Check the feeler wedge for any damage.
Check the KickbackStop function (see Sec
tion 8.7).
After the kickback stop function has uninten
tionally been triggered
Release the on/off switch and wait until the
kickback stop function status LED is no lon
ger flashing.
Check whether there was an unintentional
triggering of the kickback stop function (see
Section 8.4) or a kickback.
Try first to continue working with an active
kickback stop function. Only deactivate the
kickback stop function if you are working
without a rail and your workpiece is so un
even that the kickback stop function would
unintentionally be triggered several times
(see Section 8.6).
8.6 Working without the kickback stop
function
WARNING
Risk of injury
If the kickback stop function is deactivated,
the saw blade is not stopped when it unin
tentionally lifts.
Only deactivate the kickback stop function
if you are working without a rail and your
workpiece is so uneven that the kickback
stop function would unintentionally be trig
gered several times.
Deactivate the kickback stop function
Press the kickback stop function OFF but
ton.
English
29
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TSC 55 KEB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TSC 55 KEB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info