778530
30
Verklein
Vergroot
Pagina terug
1/185
Pagina verder
Press and hold the on/off switch within
ten seconds.
The kickback stop function remains deactivated
until the on/off switch is next released.
The kickback stop function can only be de
activated before the saw is switched on.
8.7 Checking the kickback stop function
WARNING
Risk of injury from a protruding saw blade.
Before the function testing, set the cutting
depth to 0 mm .
We recommend removing the saw blade
before the function testing.
Set the cutting depth to 0 mm.
Position the machine on a level and firm
surface.
Switch on the machine.
Press the kickback stop function OFF button
four times at intervals of at least 0.5 sec
onds within five seconds.
The kickback stop function status LED flashes
alternately red and green.
Within 15 seconds
Press the saw unit down.
Lift the machine at the rear and lower it
again.
A signal sounds, the status LED lights up green.
The kickback stop function operates fault-free.
If no signal sounds and the status LED does not
switch to green, the kickback stop function is
not operating fault-free.
Check whether the function testing was car
ried out correctly.
Clean the feeler unit behind the saw blade
(see "Changing the saw blade").
If the function testing remains unsuccessful,
the machine must no longer be used. Contact
your Festool service workshop.
8.8 Sawing along the scribe mark
The gauge marker [9-2] displays the cutting
line for 0° and 45° cuts (without a guide rail).
8.9 Cutting sections
Position the machine with the front part of the
saw table on the workpiece, switch on the ma
chine, push it down to the set cutting depth and
push it forward in the cutting direction.
8.10 Sawing cut-outs (plunge cuts)
In order to avoid kickbacks, the following
instructions must always be followed
when plunge cutting:
Always position the machine with the rear
edge of the saw table against a fixed stop.
When working with the guide rail, position
the machine at the FS-RSP kickback stop
(accessory) [11-4], which is clamped to the
guide rail.
Procedure
Place the machine on the workpiece and
position it at a stop (kickback stop).
Switch on the machine.
Slowly push the machine down to the set
cutting depth and push it forward in the cut
ting direction.
The marks [9-1] indicate the absolute front and
rear cutting points of the saw blade (Ø 160 mm)
when using the saw at maximum cutting depth
with the guide rail.
8.11 Gypsum and cement-bound fibreboards
Due to the high volume of dust, it is recommen
ded to use the cover ABSA-TS55/60 (accesso
ries) which can be mounted at the side at the
protective cover and a Festool mobile dust ex
tractor.
9 Service and maintenance
WARNING
Risk of injury, electric shock
Always remove the battery pack from the
power tool before performing any mainte
nance or service work.
All maintenance and repair work which re
quires the motor housing to be opened
should always be carried out by an author
ised service workshop.
Customer service and repairs must
only be carried out by the manufac
turer or service workshops. Find the
nearest address at:
www.festool.co.uk/service
Always use original Festool spare
parts. Order no. at:
www.festool.co.uk/service
Observe the following instructions:
Damaged safety devices and parts, such as
a faulty lever for changing tools [1-5], must
English
30
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TSC 55 KEB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TSC 55 KEB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info