778530
31
Verklein
Vergroot
Pagina terug
1/185
Pagina verder
be properly repaired or replaced in a recog
nised specialist workshop, unless otherwise
indicated in the operating manual.
Check the condition and fault-free function
ing of the recuperating springs, which push
the entire drive mechanism bearing into the
upper protected end positions.
To ensure constant air circulation, always
keep the cooling air openings in the housing
clean and free of blockages.
Use an extractor on all openings in order to
remove wood chips and splinters from the
power tool. Never open the protective
lid [1-22].
Keep the contacts on the power tool, charg
er and battery pack clean.
When working with plaster- and cement-
bonded fibreboards, clean the tool particu
larly thoroughly. Clean the vents of the
power tool and on/off switch using dry, oil-
free compressed air. Otherwise, gypsum
dust deposits may build up inside the power
tool's housing and on the on/off switch and
harden when exposed to humidity. This may
impair the switching mechanism
9.1 Reconditioned saw blades
You can use the adjusting screw [10-1] to pre
cisely set the cutting depth for reconditioned
saw blades.
Set the cutting depth stop [10-2] to 0 mm
(with guide rail).
Unlock the saw unit and push it downwards
as far as the stop.
Screw the adjusting screw [10-1] in until
the saw blade comes into contact with the
workpiece.
9.2 Saw table wobbles
The saw table must be on an even surface
when adjusting the cutting angle.
If the saw table wobbles, the setting must be
implemented again (Section 7.3).
10 Accessories
Always use accessories and consumable mate
rials approved by Festool. See Festool cata
logue or www.festool.com.
The power tool may become unsafe and lead to
serious accidents if other accessories and con
sumables are used.
In addition to the accessories described,
Festool also provides a comprehensive range of
system accessories that allow you to use your
machine more effectively and in diverse appli
cations, e.g.:
Parallel stop, table widener PA-TS 55
Side-mounted cover, false joint ABSA-TS
55
Kickback stop FS-RSP
Parallel stop FS-PA and guide extension
FS-PA-VL
Multifunction table MFT/3
10.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli
cations and these are specially designed for
your Festool saw.
10.2 Guide system
The guide rail enables you to make clean, accu
rate cuts while simultaneously protecting the
surface of the workpiece from damage.
In conjunction with the extensive range of ac
cessories, exact angled cuts, mitre cuts and fit
ting work can be completed with the guide sys
tem. The option of attaching the guide rail se
curely using clamps [11-5] ensures safer work
ing conditions.
Adjust the guide play between the saw table
and the guide rail using the two adjustable
jaws [11-1].
Bed in the splinter guard [11-3] before using
the guide rail for the first time:
Set the machine speed to 6.
Place the machine at the rear end of the
guide rail together with the complete guide
plate.
Switch on the machine.
Push down the machine slowly to the max.
preset cutting depth and cut along the full
length of the splinter guard without stop
ping.
The edge of the splinter guard now corresponds
exactly to the cutting edge.
Position the guide rail for sawing the
splinter guard on a test piece of wood.
11 Environment
Do not dispose of the device in the
household waste! Recycle devices, ac
cessories and packaging. Observe appli
cable national regulations.
EU only: In accordance with the European Di
rective on waste electrical and electronic
equipment and implementation in national law,
used power tools must be collected separately
English
31
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TSC 55 KEB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TSC 55 KEB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info