778530
27
Verklein
Vergroot
Pagina terug
1/185
Pagina verder
Colour Material Symbol
Yellow Wood
Red Laminate, mineral ma
terial
HPL/TRESPA
®
Green Plaster- and cement-
bonded chipboard and
fibreboard
Blue Aluminium, plastic
"$3:-
7.5 Changing the saw blade [5]
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
Remove the saw blade
Swivel the saw to 0° before replacing the
saw blade and adjust the maximum cutting
depth.
Turn the lever [5-2] as far as it will go. Op
erate the lever only when the saw is at a
standstill!
Push the saw unit down until it engages.
The saw unit is located in the upper locking po
sition [A].
Loosen the screw [5-8] using the Allen key
[5-2].
Remove the saw blade [5-7].
Cleaning the feeler unit
WARNING! Any contamination of the feeler unit
may impair the kickback stop function and
therefore prevent the saw blade from being
stopped.
Hold the saw unit securely by its handle,
close the lever [5-2] and press the saw unit
all the way down.
Release the lever [5-2] again and click the
saw unit into place.
The saw unit is located in the lower locking po
sition [B].
Clean the feeler unit [5-4] by blowing it out
or using a brush.
Inserting the saw blade
WARNING! Check the screws and flange for
contamination and only use clean and undam
aged parts.
Hold the saw unit securely by its handle and
turn the lever [5-2] as far as it will go.
Return the saw unit to the upper locking po
sition.
Insert a new saw blade.
WARNING! The direction of rotation of the
saw blade [5-6] and saw [5-3] must match.
Serious injuries may occur in the event of
non-compliance.
Insert the outer flange [5-5] in such a way
that the pulling peg engages in the recess
of the inner flange.
Tighten the screw [5-8].
Hold the saw unit securely by its handle,
close the lever [5-2] and guide the saw unit
back upwards.
7.6 Fitting the viewing window/splinter
guard
The viewing window (transparent) [6-1] pro
vides a view of the saw blade and optimises
dust extraction.
With 0° cuts, the splinter guard (green) [6-2]
also improves the quality of the cutting edge of
the sawn-off workpiece on the upper side.
Insert the splinter guard [6-2].
Screw the rotary knob [6-3] through the
long hole in the splinter guard.
Make sure that the nut [6-4] is seated se
curely in the splinter guard.
CAUTION! Only use the rotary knob sup
plied with your plunge-cut saw. The rotary
knob of another saw may be too long and
jam the saw blade.
Sawing a splinter guard
You must bed in the splinter guard before using
it:
Set the machine to maximum cutting depth.
Set the machine speed to 6.
Place the machine for sawing the splinter
guard on a test piece of wood.
English
27
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TSC 55 KEB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TSC 55 KEB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5.51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info