763696
14
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
14
EN
Keep clear of the saw chain as it will start
rotating upon starting of engine.
1) Fill fuel and chain oil tanks respectively, and
tighten the caps securely.
2) Set the switch to “I” position.
3) Pull out the choke knob to the closed position.
4) While holding the saw unit securely on the
ground, pull the starter rope vigorously.
5) When engine has ignited first, pull the throttle
lever to return the choke knob to the open
position and then pull the starter again to start
the engine.
6) Allow the engine to warm up with the throttle
lever pulled slightly.
Switching off the engine
1) Release the throttle lever to allow the engine to
idle for a few minutes.
2) Set the switch to the “O” (STOP) position.
Chain oil
Fig. 6a
Make sure to set up the bar and the
chain when checking the oil supply. If
not, the rotating parts may be exposed. It
is very dangerous.
After starting the engine, run the chain at medium
speed and see if chain oil is scattered off as
shown in the figure 6a.
Chain oil flow adjusting
Fig. 6b
The chain oil flow can be changed by inserting a
screw-driver in the hole on bottom of the clutch
side. Adjust according to your work conditions.
The oil tank should become nearly empty
by the time fuel is used up. Be sure to
refill the oil tank every time when
refueling the saw.
Carburetor
Fig. 7
Be sure to adjust the carburetor with the
bar chain attached.
The carburetor on your unit has been factory
adjusted, but may require fine tuning due to a
change in operating conditions. Before adjusting
the carburetor, make sure that the provided
air/fuel filters are clean and fresh and the fuel
properly mixed.
When adjusting, take the following steps:
1) H and L needles are restricted within the
number of turn as shown below.
H needle: -1/4 -1/4
L needle: -1/4 -1/4
2) Start the engine and allow it to warm up in low
speed for a few minutes.
3) Turn the idle adjusting screw counterclockwise
so that the saw chain does not turn. If the idling
speed is too slow, turn the screw clockwise.
4) Make a test cut and adjust the H needle for
best cutting power, not for maximum speed.
Chain brake operational test
Fig. 8
Test the chain brake periodically to
ensure correct function.
Place the saw on a clear, firm, flat surface and
then start the engine.
Grasp the rear handle with your right hand and
with your left hand, hold the front handle safely
and firmly.
Let the engine run at mid revs.
Squeeze the chain brake lever to the front. The
saw chain should abruptly stop.
Then depress the trigger to “IDLE” and release
the chain brake.
If the chain does not stop, turn the
engine off and take your unit to the
nearest authorized service centre for
service. The saw must not be used.
WORKING INSTRUCTIONS
Felling requires extensive experience.
Both, felling and limbing must only be
carried out by trained persons.
Courses for working with chainsaws and
courses for felling trees are regularly
offered by local professional
organisations.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CSM1045 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CSM1045 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info