763696
13
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
13
EN
4) Pour in the rest of gasoline and agitate again
for at least one minute. As some oils may be
difficult to agitate depending on oil ingredients,
sufficient agitation is necessary for the engine
to last long. Be careful that, if the agitation is
insufficient, there is an increased danger of early
piston seizing due to abnormally lean mixture.
5) Put a clear indication on the outside of the
container to avoid mixing up with gasoline or
other containers.
6) Indicate the contents on outside of container
for easy identification.
Shake the mixture correctly before
pouring it into the fuel tank.
Fuel Storage
Fuel can be stored for a limited time period only.
Fuel and mixtures get old. Old fuel mixture can
cause problems during starting of the chainsaw.
Mix only as much of the mixture as you need for
the following 4 week period.
Fueling the unit
Fig. 4
1) Untwist and remove the fuel cap. Rest the cap
on a dustless place.
2) Put fuel into the fuel tank to 80% of the full
capacity.
3) Fasten the fuel cap securely and wipe up any
fuel spillage around the unit.
Select flat and bare ground for fueling.
Move at least 10 feet (3 meters) away
from the fueling point before starting the
engine.
Stop the engine before refueling the unit.
At that time, be sure to sufficiently
agitate the mixed gasoline in the
container.
Saw chain oil
Fig. 4
Use motor oil SAE #10W-30 all year round or SAE
#30 ~ #40 in summer and SAE #20 in winter.
Do not use wasted or regenerated oil
that can cause damage to the oil pump.
To enable sufficient oil lubrication of the saw
chain, there must be a sufficient amount of oil in
the tank.
Whenever filling the fuel mixture to the
tank, also replenish the oil for saw
chains.
To oil the chain saw and guide bar, use only
ecological, biologically degradable oil for saw
chains, then eventually oil for saw chains on the
basis of mineral oils (ISO VG 100).
Oils for saw chains stick when not used
for a long time. This can cause damage
to the oil pump or parts using the oil.
How to avoid it:
Empty the oil for saw chains out of the oil tank
of the chain saw.
Replenish the tank with a little engine oil.
Allow the chain saw to run for some time
to enable the oil to flow and to clean the oil
pump.
Before further use of the chain saw, again
replenish the tank with oil for saw chains.
4. OPERATION
Engine start
Fig. 4, 5a, 5b
Before starting the saw be sure to loosen
the chain brake. The safety cover should
be pulled to the front handle.
It is very dangerous to run a chainsaw
that mounts broken parts or lacks any
parts. Before starting engine, make sure
that all the parts including bar and chain
are installed properly.
When restarting immediately after
stopping the engine, leave the choke
knob at the open position.
When restarting immediately after
stopping the engine, leave the choke
knob at the open position.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CSM1045 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CSM1045 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info