763696
16
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
16
EN
Felling
Fig. 9a
Felling consists of 2 main cutting
operations: making 2 notching cuts and
making one felling cut.
For felling cuts and cross cuts, the spike
bar must safely adhere to the cut wood.
The felling cut must be made in the
desired fall direction as close to the
ground as possible.
First cut the felling notch obliquely from above,
then horizontally.
Cut the felling cut horizontally in the opposite
direction to the felling notch. The cut must be
made ca 3-5 cm higher than the horizontal
notch.
There must be a joint bar between the
notch and the cut, whose width is ca
1/10 of the tree trunk diameter.
If the tree starts falling during the cut,
immediately remove the chainsaw from the
cut and leave via the safety route away from
danger.
Beware of falling branches.
If the tree remains standing, fell it by using
wedges which are driven into the felling cut.
Beware of falling branches.
Bucking and Limbing
Always ensure your foothold. Do not
stand on the log.
Be alert to the rolling over of a cut log.
Especially when working on a slope,
stand on the uphill side of the log.
Follow the instructions in “For Safe
Operation” to avoid kickback of the saw.
A log lying off the ground
Fig. 9b
Before starting work, check the direction of
bending force inside the log to be cut. Always
finish cutting from the opposite side of the
bending direction to prevent the guide bar from
being caught in the cut.
A log hanging off the ground
Fig. 9c
Saw down halfway, then roll the log over and cut
from the opposite side.
In area A, saw up from the bottom one-third and
finish by sawing down from the top .In area B, saw
down from the top one-third and finish by sawing
up from the bottom.
Cutting the limbs of Fallen Tree
Fig. 9d
First check to which side the limb is bent. Then
make the initial cut from the bent side and finish
by sawing from the opposite side.
Be alert to the springing back of a cut
limb.
Pruning of Standing Tree
Fig. 9e
Cut up from the bottom, finish down from the top.
Do not use an unstable foothold or
ladder.
Do not overreach.
Do not cut above shoulder height.
Always use both your hands to
hold the saw.
5. MAINTENANCE
Troubleshooting, Causes and Repairs
Before any maintenance and cleaning
work unplug the connector of the spark
plug!
Before any maintenance work on the
chain saw:
Stop the engine and allow it to cool a little,
Unplug the connector of the spark plug,
Wear protective gloves.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CSM1045 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CSM1045 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info