763696
11
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
11
EN
Mass (without guide bar and
chain and with empty tank) 6.2kg
Guaranteed sound power level,
LWA (2000/14/EC) LwA: 117 dB(A)
Level of sound pressure LPA 101 dB (A)
Vibration acceleration avhw 9.68 m/s2
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardized test given in
EN60745; it may be used to compare one tool
with another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned.
Using the tool for different applications, or with
different or poorly maintained accessories,
may significantly increase the exposure level.
The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
Description
The numbers in the text refer to the diagrams on
pages 2-7
1. Saw chain
2. Guide bar
3. Fuel tank cap
4. Front handle
5. Primer (starter pull rope)
6. Air filter cover
7. Starter grip
8. Choke knob
9. Switch
10. Throttle trigger interlock
11. Guide bar cover
12. Oil tank cap
13. Starter cover
14. Saw chain tensioner screw
15. Chain brake
16. Spike bar
17. Bar retaining nuts
18. Chain catcher
19. Muffler
20. Throttle trigger
21. Rear handle
3. ASSEMBLY
Guide bar and saw chain assembly
Fig. 2a - 2d
The saw chain has very sharp edges. Use
thick protective gloves for safety.
Before starting any work on the guide
bar and the saw chain:
Stop the engine,
Unplug the spark plug connector,
Put protective gloves on.
Observe the run direction of the saw chain.
The cutting edges of the saw teeth on the top
side of the guide bar lead to the front to the
reversible star (the end of the bar).
1) Pull the guard towards the front handle to
check that the chain brake is not engaged.
2) Loosen the nuts and remove the chain cover.
3) Install the attached spike to the power unit.
4) Gear the chain to the sprocket and, while
fitting the saw chain around the guide bar,
mount the guide bar to the power unit. Adjust
the position of chain tensioner nut on the chain
cover to the lower hole of guide bar.
Pay attention to the correct direction of
the saw chain.
5) Fit the chain cover to the power unit and fasten
the nuts to finger tightness.
6) While holding up the tip of the bar, adjust the
chain tension by turning the tensioner screw
until the tie straps just touch the bottom side
of the bar rail.
7) Tighten the nuts securely with the bar tip
held up (12 ~ 15 Nm). Then check the chain
for smooth rotation and proper tension while
moving it by hand. If necessary, readjust with
the chain cover loose.
8) Tighten the tensioner screw.
A new chain will expand its length in the
beginning of use. Check and readjust the
tension frequently as a loose chain can
easily derail or cause rapid wear of itself
and the guide bar.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CSM1045 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CSM1045 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info