536726
15
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
13
2. Fit the 3.6V Lithium battery supplied, with the
negative (-) towards the battery spring.
3. Mount the Detector to the fixed part of the frame
along the opening edge opposite the hinges using
either the double sided adhesive tape or screws
provided.
If fixing the Detector with screws; fit the Keyhole
slot in the top of the Detector over the head of the
smaller pan-head screw. Secure the bottom of
the Detector using the 12mm countersunk head
screw fitted within the battery compartment. You
will need to drill out the centre of the fixing screw
hole using a 3mm drill. Do not over tighten the
fixing screws as this may distort or damage the
casing.
4. Fit the Magnet to the moving part of the
door/window opposite the Detector using the
adhesive tape or 15mm fixing screws.
Ensure that the parallel gap between the Magnet
and Detector is less than 10mm and that the arrow
on the Magnet is pointing towards and aligned with
the mark on the Detector.
5. If several windows need to be protected, remove
the self-contained wired supplied and adopt the
wire according to the specifications as mentioned
below. This should be wired to the terminal block
provided in the battery compartment in series
connection. The wired contact should be
connected using two core (24AWG) wire of
maximum length 1.5m.
A cable entry cut-out is available and adjacent to
the terminal block.
6. Refit the battery cover.
SETTING THE MAGNETIC CONTACT
DETECTORS
1. Located on the PCB of the Detector is a
two-position DIP switch (SW2).
2. DIP switches 1-2 are used to enable/disable the
internal or external wired magnetic contact.
On/Off
Selection
DIP1 of SW2 DIP 2 of SW2
ON Internal on External on
OFF Internal off External off
Internal connection External wired connection
If setting the DIP1 & DIP2 to ‘Off’, only the internal
contact will be active. When two contacts are in
use for internal and external connection
simultaneously, one activation will be counted if one
of the contacts is opened; while both contacts must
be all close, the Detector will then be treated as
close.
3. If external contacts are wired to the Detector, set
the DIP1 to ‘Off’ and DIP2 to ‘On’.
IMPORTANT: If external contacts are not
connected, set the DIP1 to ‘On’ and DIP2 to ‘Off’
for the detector to operate correctly.
4. In order to communicate with the Smart Home Box,
the ID code of the Detector needs to be learned by
the Smart Home Box. To proceed with ID code
learning:
a. Set the Smart Home Box into ‘3. Security
Sensor Zone’ and press .
15

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-HIS20SF

Zoeken resetten

  • wij hebben een his20s alarmsysteem , volgens mij kon ik daar vroeger op inloggen ?
    kan iemand mij daar mee helpen
    marc Gesteld op 23-11-2023 om 16:54

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro HIS20SF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro HIS20SF in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info