536726
13
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
11
Set the required sensitivity detection using DIP2 of
SW2 as follows:
ON high sensitivity detection
OFF low sensitivity detection
Note: The higher the sensitivity detection the less
movement will be necessary before the PIR
detector will trigger the alarm.
3. The setting of the DIP1 & DIP2 of SW2 can be
distinguished from the LED indication as follows:
On/Off
Selection
DIP1 of
SW2
DIP2 of
SW2
Trigger reaction of LED
High
Sensitivity
LED will be on once.
It implies high
sensitivity.
ON Walk Test
mode
Low
Sensitivity
LED will flash twice. It
implies low sensitivity.
OFF Normal
mode
High/Low
Sensitivity
LED does not light up.
In summary, the setting of DIP1 & DIP2 of SW2 is
concluded as below:
SW2 DIP1 DIP2
ON Walk Test Mode High sensitivity
OFF Normal Mode Low sensitivity
4. Connect the 1/2 3.6V Lithium battery to the battery
spring.
Note: When the battery is connected, the LED
behind the lens will flash for 2-3 minutes as
warming-up duration until the PIR has stabilized
when the LED will then stop flashing and turn OFF.
5. In normal mode, remove the rear cover of the PIR
detector. The Detector’s LED will illuminate and the
Smart Home Box should beep. It is because the
tamper switch fitted on the Detector has been
activated.
6. When the Detector is fully installed i.e. battery
cover is refitted; the Detector will not detect
movement for approximately 2 minutes after each
activation. (This feature is present to conserve
battery power and maximize the battery life).
7. In order to communicate with the Smart Home Box,
the ID code of the Detector needs to be learned by
the Smart Home Box. To proceed with ID code
learning.
a. Set the Smart Home Box into ‘3. Security
Sensor Zone’ and press .
b. Select ‘3-1 Wireless Sensor Zone’ and
press .
c. ‘Input (01-32) Sensor Zone’ and press .
d. An indication of ‘:1 Learning ID’ will be shown
and press .
By pressing tamper switch located adjacent to the
PCB on the Detector will emit the ID code to the
Smart Home Box instantly.
8. For quick start, jumper link (S2) will quick start the
battery this will take approx. 2 minutes. By
placing the jumper link (S2) into position, the LED
adjacent to the (S2) jumper link will become
illuminated, this implies the battery start up has
been completed. It is important to remove the
jumper link (S2) after this has been observed to
save battery power.
Jumper link (S2)
Note: On first battery start up, because of the
nature of the battery protection the battery may
incur a low battery status and may not start up
straight away, but will automatically start within 10
minutes.
Note: Only one of pins of Jumper link (S2) will be
inserted in position as factory default setting.
TESTING THE PIR DETECTORS
Ensure that the system is in Test Mode.
With the PIR detector set in Test mode and mounted in
position on the wall, allow 2-3 minutes for the detector
to stabilize before commencing the Walk Test.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-HIS20SF

Zoeken resetten

  • wij hebben een his20s alarmsysteem , volgens mij kon ik daar vroeger op inloggen ?
    kan iemand mij daar mee helpen
    marc Gesteld op 23-11-2023 om 16:54

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro HIS20SF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro HIS20SF in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info