536726
16
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
14
b. Select ‘3-1 Wireless Sensor Zone’ and
press .
c. ‘Input (01-32) Sensor Zone’ and press .
d. An indication of ‘:1 Learning ID’ will be shown
and press .
By pressing tamper switch either located adjacent
to the PCB or rear cover of the Detector will emit
the ID code to the Smart Home Box instantly.
5. For quick start, jumper link (S1) will quick start the
battery this will take approx. 2 minutes. By
placing the jumper link (S1) into position, the LED
adjacent to the (S1) jumper link will become
illuminated, this implies the battery start up has
been completed. It is important to remove the
jumper link (S1) after this has been observed to
save battery power.
Jumper link (S1)
Note: On first battery start up, because of the
nature of the battery protection the battery may
incur a low battery status and may not start up
straight away, but will automatically start within 10
minutes.
Note: Only one of pins of Jumper link (S1) will be
inserted in position as factory default setting.
TESTING THE MAGNETIC CONTACT
DETECTORS
Ensure that the system is in Test Mode
1. Press
to put the system into Test mode.
‘WALK TEST’ will be displayed.
2. Press to activate Walk Test.
‘ Walk Test Waiting…’ will be displayed.
3. Remove the battery cover by sliding off. As the
battery cover is removed the LED on the Detector
will illuminate for approx. 1 second to indicate that
the tamper switch has been activated. In addition,
the Smart Home Box will chime to indicate that an
alarm signal has been received and ‘Magnetic
Contact Tamper will be displayed.
4. Open the door/window to detach the magnet from
the Detector. As the magnet is parted from the
detector the LED will illuminate for approx. 1
second to indicate that the Detector has been
triggered. In addition, the Smart Home Box will
chime to indicate that an alarm signal has been
received and the identity of the zone that the
detector is set for will be displayed.
Note: In normal mode with the battery cover fitted,
the LED on the detector will not illuminate when
the detector is triggered, (unless the battery is
low).
5. If connected, operate the wired Magnetic Contact.
As the contact is opened the LED on the Detector
should illuminate for 1 second to indicate that it has
been triggered and the Smart Home Box will
acknowledge the alarm signal.
6. Refit the battery cover on the Detector.
7. Press to return to the top level menu of
TEST MODE.
ON/OFF RECEIVER
It is a plug-in receiver to receive the Radio Frequency
signal from the Smart Home Box and through the
Smart Home Box controls the On/Off status of the
plug-in light fixture or home appliances.
INITIAL POWER UP
Plug the receiver to the electrical outlet, the LED on the
receiver will be flashing slowly. This implies that the
receiver does not memorize any ID code and cannot
be controlled by the Smart Home Box. However,
pressing the On/Off knob will control directly the On/Off
16

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-HIS20SF

Zoeken resetten

  • wij hebben een his20s alarmsysteem , volgens mij kon ik daar vroeger op inloggen ?
    kan iemand mij daar mee helpen
    marc Gesteld op 23-11-2023 om 16:54

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro HIS20SF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro HIS20SF in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info