723580
9
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
ENGLISH
7
Chisel Bit adjustment ( )
D25831, D25851
Turn the mode selector to one of the chisel bit adjustment
icons to adjust the chisel to the desired position. There are
multiple positions to set the angle of the chisel. After finding
the desired position, slightly maneuver the chisel bit back
and forth to ensure the chisel is properlyengaged.
Indicator Lights (Fig. A, E)
The yellow brush wear indicator LED 10  lights up when
the carbon brushes are nearly worn out indicating that the
tool needs servicing within the next 8 hours ofuse.
The red indicator LED 9  lights up if the lock-on slider2
and/or E-Clutch™ is engaged in any mode except the
chippingmode.
The red indicator LED 9  starts to flash if there is a fault with
the tool or the brushes have completely worn out (refer to
Repairs underMaintenance).
INDICATOR DIAGNOSIS SOLUTION
OFF Tool is functioning
normally
Follow all
warnings and
instructions when
operating tool
SOLID Perform and protect
control has been
activated
With tool properly
supported, release
trigger; the tool
will function
normally when
the trigger is
depressed again
and the indicator
light will go out
FLASHING Perform and
protect control is
malfunctioning
Take the tool to
an authorized
DeWALT
repairagent.
NOTE: If the tool power is insufficient for normal
hammering and if the LED does not flash repeatedly after
cycling the trigger, take the tool to an authorized D
e
WALT
repaircenter.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.
WARNING: To reduce the risk of personal injury,
ALWAYS ensure workpiece is anchored or
clamped firmly. If hammerdrilling thin material,
use a wood “back-up” block to prevent damage to
thematerial.
WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the side handle
properly installed and securely tightened. Failure
to do so may result in the side handle slipping during
tool operation and subsequent loss of control. Hold
tool with both hands to maximizecontrol.
WARNING: Drill may stall if overloaded causing a
sudden twist. Always expect the stall. Grip the drill
firmly with both hands to control the twisting action
and avoidinjury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the side
handle3, with the other hand on the main handle4.
Fig. F 4
4
3
3
NOTE: Operating temperature of this tool is 19˚F to 104˚F
(-7˚C to +40˚C). Using the tool outside of this temperature
range will decrease the life of thetool.
Trigger Switch (Fig. A)
D25501, D25553, D25601, D25603,
D25651
To turn the tool on, depress the trigger switch1. To stop
the tool, release the triggerswitch.
In chipping mode only, lock the trigger switch on by
pushing the lock-on slider2 upward while depressing the
triggerswitch.
To deactivate the lock-on slider, depress the trigger switch
once thenrelease.
The lock-on slider may only be activated in chipping mode.
The machine will stop running when trying to engage the
lock-on slider in hammerdrilling mode. The motor will stop
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D25553 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D25553 in de taal/talen: Engels, Frans, Spaans, Alle talen als bijlage per email.

De handleiding is 2,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info