723580
10
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
ENGLISH
8
if the lock-on slider is activated when changing from chisel
mode into hammerdrillingmode.
D25831, D25851
For continuous operation, move the toggle switch1 to the
on position. To stop continuous operation, move the toggle
switch to the offposition.
Soft Start Feature
The soft start feature allows you to build up speed slowly,
thus preventing the drill bit from walking off the intended
hole position when starting. The soft start feature also
reduces the immediate torque reaction transmitted to the
gearing and the operator if the hammer is started with the
drill bit in an existinghole.
Hammerdrilling with a Solid Bit (Fig. A, E)
D25501, D25553, D25601, D25603,
D25651
NOTE: The D25831 and D25851 have only chipping modes
with no hammerdrillingcapability.
1. Set the mode selector6 to hammerdrillingmode.
2. For D25603 and D25651 only, move the torque control
lever 8  to Setting 1 14 .
3. Set the speed and impact control dial7.
4. Insert the appropriate drillbit.
5. Adjust the side handle (front or rear position)3.
6. Mark the spot where the hole is to bedrilled.
7. Place the drill bit on that mark and depress the trigger
switch1.
8. Apply only enough pressure to engage active
vibration control (refer to SHOCKS Active Vibration
Control®System).
9. To stop the tool, release the trigger switch.
Always turn the tool off when work is finished and
beforeunplugging.
Hammerdrilling with a Core Bit (Fig. A, E)
D25501, D25553, D25601, D25603,
D25651
CAUTION: Do not use a core bit for hammerdrilling
wood. Personal injury and damage to tool mayresult.
NOTE: The D25831, D25851 have only chipping modes with
no hammerdrillingcapability.
1. Set the mode selector6 to hammerdrillingmode.
2. For D25603 and D25651 only, move the torque control
lever 8  to Setting 2 11 .
3. Turn the speed and impact control dial7 to the
desiredspeed.
4. Adjust the side handle (front or rear position)3.
5. Assemble the centering bit and adapter shank into
corebit.
6. Mark the spot where the hole is to bedrilled.
7. Place the centering bit on that mark and depress the
trigger switch1.
NOTE: Some core drills require the removal of centering
bit after about 1 cm of penetration. If so, remove and
continuehammerdrilling.
8. When hammerdrilling through a structure thicker than
the depth of the core bit, break away the round cylinder
of concrete or core inside the bit at regular intervals. To
avoid unwanted breaking away of concrete around the
hole, first drill a hole the diameter of the centering bit
completely through the structure. Then drill the cored
hole halfway from each side of thestructure.
9. To stop the tool, release the trigger switch.
Always turn the tool off when work is finished and
beforeunplugging.
Chipping and Chiseling (Fig. A)
D25831, D25851
1. Set the mode selector6 to chippingmode.
2. Set the impact control dial7 to desired setting (refer to
Electronic Speed and ImpactControl).
3. Insert the appropriate chisel and rotate it by hand to
lock it into the desiredposition.
NOTE: For SDS Max models, only use SDS Maxbits.
4. Adjust the side handle (front or rear position)3.
5. Depress the trigger switch1.
6. Apply only enough pressure to engage active
vibration control (refer to SHOCKS Active Vibration
Control®System).
7. To stop the tool, release the trigger switch.
Always turn the tool off when work is finished and
beforeunplugging.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performingthis.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D25553 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D25553 in de taal/talen: Engels, Frans, Spaans, Alle talen als bijlage per email.

De handleiding is 2,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info