723580
7
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
ENGLISH
5
12
3
18 D25831
D25501, D25601,
D25603, D25820
3
12
16
Fig. B
SHOCKS Active Vibration Control® System
(Fig. A, F)
D25651, D25601, D25603, D25831,
D25851
For best vibration control, hold the tool with one hand
on the main handle4 and the other hand on the side
handle3. Apply just enough pressure so the damping
device on the main handle is approximately mid stroke. The
hammer only needs enough pressure to engage the active
vibration control. Applying too much pressure will not make
the tool drill or chip faster and active vibration control will
notengage.
Inserting and Removing Spline Drive
Accessories (Fig. C)
D25553, D25651, D25851
WARNING: Burn hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and
bits may get extremely hot during operation. Small
bits of broken material may damage barehands.
WARNING: Do not attempt to tighten or loosen drill
bits (or any other accessory) by gripping the front part
of the chuck and turning the tool on. Damage to the
chuck and personal injury mayoccur.
1. Insert the bit shank into the tool holder13 as far as
it will go. The groove on the chisel shank 17  must
be aligned with the symbol 15  on the toolholder. If
inserted correctly, the locking sleeve16 moves back to
the end position and shows a closed locksymbol.
2. Pull on the bit to be sure that it is properlylocked.
3. If the chisel groove is not aligned with the symbol, or
is not inserted to the complete depth the lock symbol
remainsopen.
4. To remove the bit, pull back the locking sleeve and pull
the bitout.
Fig. C 13
17
15
16
Inserting and Removing SDS Max
Accessories (Fig. D)
D25501, D25601, D25603, D25831
1. Pull back the locking sleeve16 and insert the bit shank.
The bit shank must beclean.
2. Turn the bit slightly until the sleeve snaps back
intoposition.
3. Ensure the bit is properlyengaged.
NOTE: The bit needs to move several centimeters in and
out of the tool holder13 when properlyengaged.
4. To remove the bit, pull back the locking sleeve and pull
the bitout.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D25553 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D25553 in de taal/talen: Engels, Frans, Spaans, Alle talen als bijlage per email.

De handleiding is 2,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info