697434
37
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
Commissioning
6720813171 (2016/05) 37
10 Commissioning
This section explains how to start up the boiler.
Complete the commissioning record log book after carrying out the
activities described below ( section 10.5 “Commissioning record
log book”, page 45).
10.1 Filling the heating system
10.1.1 Filling the heating system
The pre-pressure of the expansion vessel must be at least equal to the
static pressure (system height to the centre of the expansion vessel),
however never less than 0.5 bar.
Push on the control panel to open it ( fig. 68).
Turn the maximum CH flow temperature dial [8] and DHW
temperature dial [10] anticlockwise to the “0” position.
Fig. 70 BC10 basic controller
Turn the vent key through a quarter rotation [1] to undo the boiler
door lock ( detailed picture).
Push the fastener down [2] and open the boiler door [3].
Remove the insulation cover of the pump group [4].
Fig. 71 Opening the boiler door
The boiler has an automatic air vent to purge the boiler.
To purge the boiler, every radiator in the heating system must have a
purge facility. In some situations it may even be necessary to provide
extra purging facilities at certain locations.
Turn the cap of the automatic air vent through one rotation to loosen
it.
Fig. 72 Opening the automatic air purging unit
Filling and refilling of the heating circuit must have been carried out by a
method that has been approved by the Water Regulation Advisory
Scheme (WRAS), for the type of heating appliances, i.e. Domestic
(in-house) Fluid Category 3. Non-Domestic (other than in-house) Fluid
Category 4. Depending on the Fluid Category the approved method
should comprise of the following:
Requirements Fluid Category 3 systems
Control valve (stop valve) including a double check valve on the
mains cold water supply pipe.
Temporary connection to be removed after filling (filling loop).
Control valve (stop valve) on the heating system pipework.
Fig. 73 System fill - category 3
Requirements Fluid Category 4 systems
Control valve (stop valve) on the mains cold water supply pipe.
•Strainer.
Water non-return valve with reduced pressure Zone (RPZ valve
assembly) incorporating a Type BA air gap.
•Tundish.
Control valve (stop valve) on the heating system pipework.
Fig. 74 System fill - category 4
If a fault occurs, then refer to the servicing manual or
contact Worcester.
At initial start up, the boiler will start up as soon as the
system pressure exceeds 1.0 bar. If the system pressure
falls to below 0.2 bar the boiler will stop and generate a
fault code.
888
1
10
9
8
7
6
5432
1
6 720 648 726-069.1TD
11
1.
2.
3.
4.
6 720 648 726-071.1TD
6 720 648 726-072.1TD
Heating return
SYSTEM FILL
Hose
return
Stop
cock
Test cock
Non return
valve
Non return
valve
Mains
supply
Temporary hose
Stop cock
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worcester-Bosch GB162-80 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worcester-Bosch GB162-80 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Worcester-Bosch GB162-80

Worcester-Bosch GB162-80 Installatiehandleiding - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info