697434
29
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
Installation
6720813171 (2016/05) 29
Connect the black pre-wired main appliance lead to a permanent live
supply (from the same fused isolator as all other controls on the
heating system), L N E.
Remove the grey cover of the 230 Volt converter [1].
Feed the 230 V switch live and neutral (from external controls)
through the cable gland.
Identify the 230 V terminal block by the hashed area and 230 VAC
warning triangle.
Connect the switch live to terminal “1” and a neutral to terminal “2”
[2].
Fig. 52 Connection box - 230 Volt connection
8.5.5 230 V connections (only for GB162-50/65)
Fig. 53 Terminal strip - external heating pump 230 V (connection
colour green)
Connecting an external boiler pump - general
Since the boiler has not been fitted with a pump, a pump must be
connected to the boiler.
When using a pump group with an integrated pump:
Read the assembly instructions of the pump group for the electrical
pump connections.
If you do not make use of a pump group, you can connect the external
pump in 2 ways:
to the unused 230 VAC pre-wired pump cable;
to the green PK terminal of the boiler. To connect order a PK plug
(accessory).
Proceed as follows:
The maximum electrical load that can be connected to the free 230 VAC
connection cable of the pump ( fig. 54, [1]) and to the green EP
connector ( fig. 56) is 250 Watts in total. If a load of more than
250 Watts is to be connected, this is possible by using an additional
230/230 V relay, which has to be installed by a registered installer/
electrician.
Connection to the free 230 VAC connection lead
Unwind the 230 VAC cable [1] and route it out of the boiler
( fig. 55).
Fig. 54 230 VAC cable of the pump
Cut the plug from the 230 VAC cable.
Connect the 230 VAC cable to the pump.
Fig. 55 Route the 230 VAC pump cable
WARNING:
This appliance must be earthed.
NOTICE:
Connect the 230 Volt converter (grey box) via the
pair of black low voltage cable to terminal WA.
( figure 48).
NOTICE:
Terminal 3 [2] is not used.
NOTICE:
The 230 V connections can only be used with a
corresponding control unit. If you use other than the
GB162 pump group, you must ensure that it correctly
connects to the terminal strip in fig. 53.
Observe the layout document and the installation
instructions of the control unit.
WARNING:
Do not connect a temperature controller to the 230 V
connections.
6 720 648 726-052.1TD
21
PK PS PZ
Mains
230 V
6 720 648 726-053.1TD
WARNING:
Damage to the installation by the boiler being
overloaded.
6 720 648 726-054.1TD
1
1
6 720 648 726-055.1TD
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worcester-Bosch GB162-80 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worcester-Bosch GB162-80 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Worcester-Bosch GB162-80

Worcester-Bosch GB162-80 Installatiehandleiding - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info