697462
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
9
Commissioning
CS200 – 6720830475 (2015/06)
5. Fill and vent the system.
6. Commissioning the CS 200 solar controller
( Chapter 5.2, page 9)
7. Commissioning the system with the solar controller
( Chapter 5.3, page 9)
8. Check and, if necessary, adjust the settings in the service
menu of the CS 200 solar controller and perform
configuration ( Chapter 5.4, page 10)
9. Remedy warning and fault displays, if necessary, and reset
fault history
10. System handover to end user ( Chapter 5.7, page 10).
5.2 General commissioning of the solar controller
Setting the language
Turn the rotary control knob to select a language and press
the rotary control knob.
Setting the date
Turn the rotary control knob to set the day, month and year.
Continue is highlighted.
If the date is set correctly, press the rotary control knob to
apply the date.
Setting the time
Turn the rotary control knob to set the hours and the
minutes.
Continue is highlighted.
If the time is set correctly, press the rotary control knob to
apply the time.
System configuration
Turn and press the rotary control knob to start (Yes) or to
skip the configuration wizard (No).
When the configuration wizard begins, the solar controller
automatically recognises which BUS nodes (e.g. modules)
are installed in the system (system analysis) and adjusts
the menu and the factory defaults to the current system.
Perform system commissioning ( Chapter 5.3).
5.3 System commissioning with the
configuration wizard
The solar controller automatically recognises which BUS nodes
(e.g. modules) are installed in the system. The configuration
wizard adjusts the menu and the factory defaults.
The system analysis may take up to one minute.
After the configuration wizard has performed the system
analysis, the Commissioning menu is opened. The settings
must be checked here and, if necessary, adjusted and finally
confirmed.
If the system analysis is skipped, the Commissioning menu is
opened. The settings listed here must be carefully adjusted
according to the installed system. Finally, the settings must be
confirmed.
For further information on the settings refer to the technical
documentation of the modules used.
5.3.1 Commissioning the solar heating system
Menu item
Start configuration wizard?
Question Answer / setting
Check before starting the configuration wizard:
Module installed and address set?
Temperature sensor installed?
System charged and vented?
Start the configuration
wizard?
Yes | No
Operating mode
Question Answer / setting
Which system is installed?
Is the coding switch
correspondingly set at the
solar module?
Solar | DHW
Extension module
Question Answer / setting
Is an extension module
installed? (only required if
the use of a MS100 is used
in addition to the required
MS 200)
No | MS 100
Change solar configuration
Question Answer / setting
Is the solar thermal system
correctly configured with all
functions and additional
functions?
Graphic configuration of the
solar system
Speed ctrl. solar pump
Question Answer / setting
Is a solar pump with speed
control installed?
No | PWM | 0-10 V
Speed ctrl solar pump2
Question Answer / setting
Is a solar pump with speed
control installed?
No | PWM | 0-10 V
Gross collector area 1
Question Answer / setting
How large is the gross
collector area?
0 to 500 m
2
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Worcester-Bosch CS 200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Worcester-Bosch CS 200 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Worcester-Bosch CS 200

Worcester-Bosch CS 200 Gebruiksaanwijzing - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info