738218
37
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
37
d) Impedance measurement
Make sure that all circuit parts, circuits and components and other objects of measurement are discon-
nected from the voltage and discharged.
Proceed as follows to measure a resistance:
- Switch on the DMM and select the measuring range “Ω”.
- Plug the red measuring line into the Ω measuring jack (7) and the black
measuring line into the COM measuring jack (6).
- Check the measuring lines for continuity by connecting the two measuring
prods. The impedance value must be approximately 0 - 1.5 Ohm (inherent
impedance of the measuring lines).
- Now connect the two measuring prods to the object to be measured. As
long as the object to be measured is not high-impedance or interrupted,
the measured value will be indicated on the display. Wait until the dis-
played value has stabilised. With impedances of >1 MOhm, this may take
a few seconds.
- If “O.L.” (= overow) appears on the display, you have exceeded the
measuring range or the measuring circuit is interrupted.
- Remove the measuring lines from the object to be measured after comple-
tion of the measurement and switch off the DMM.
If you perform a resistance measurement, make sure that the measuring points you touch with the
measuring prods are free of dirt, oil, solderable lacquer or similar. Such circumstances can falsify the
measured result.
e) Acoustic continuity test
Make sure that all circuit parts, circuits and components and
other objects of measurement are disconnected from the
voltage and discharged.
- Turn the DMM on and select the measuring function .
- Plug the red measuring line into the V measuring jack (7) and the black
measuring line into the COM measuring jack (6).
- A continuity value of less than approx. 50 Ohm is identied as continuity;
in this case a beep sounds. The display shows the corresponding resist-
ance up to max. 199.9 Ohm.
- If “OL” (= overow) appears on the display, you have exceeded the meas-
uring range or the measuring circuit is interrupted.
- Remove the measuring lines from the object to be measured after com-
pletion of the measurement and switch off the DMM.
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voltcraft VC165 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voltcraft VC165 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info