738218
35
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
35
b) Voltage measuring “V”
Proceed as follows to measure direct voltages “V/DC” (V ):
- Switch on the DMM and select the respective measuring
range “V
“ or “mV ”.
- Plug the red measuring line into the V measuring jack (7)
and the black measuring line into the COM measuring
jack (6).
- Connect the two measuring prods to the object to be meas-
ured (battery, circuit, etc.). The red measuring prod indicates
the positive pole, the black measuring prod the negative
pole.
- The current measured value is indicated on the display.
- Remove the measuring lines from the object to be meas-
ured after completion of the measurement and switch off the
DMM.
If a minus “-” appears in front of the measured value for direct voltage, the measured voltage is negative
(or the measuring lines are swapped).
The voltage range “V/DC” has an input resistance of >10 MOhm.
Proceed as follows to measure alternating voltages “V/AC” (V
):
- Switch on the DMM and select the respective measuring range “V
“ or “mV ”.
- For the measuring function “mV “, push the button “SELECT” once briey. The meter switches the alternating volt-
age measurement. Pushing again switches back to the direct voltage measurement.
-
Plug the red measuring line into the V measuring jack (7) and the black measuring line into the COM measuring jack (6).
- Connect the two measuring prods to the object to be measured (battery, mains voltage, etc.).
- The current measured value is indicated on the display.
- Remove the measuring lines from the object to be measured after completion of the measurement and switch off
the DMM.
The voltage range V/AC” has an input resistance of >10 MΩ.
c) Current measuring “A“
The maximum permissible voltage in the measuring circuit against ground potential must not
exceed 600 V in CAT II and III.
Current measurement always takes place in series with the consumer. Before connecting the meter, the circuit must
be powered down. After the end of measuring, power down the circuit before removing the measuring lines. This
prevents the occurrence of light arcs.
Current measurements >5 A must only be performed for max. 10 seconds and with measuring breaks of 15 minutes.
The internal resistance of the meter causes a low voltage drop in the measuring circuit (max. 200 mV) because of
the integrated fuse in the mA/µA measuring range. However, this is usually negligible.
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voltcraft VC165 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voltcraft VC165 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info