665091
7
Verklein
Vergroot
Pagina terug
1/134
Pagina verder
7
GB
2. Use the gauge on the outside of the Grinding Angle Set-Up Jig to measure the bevel angle
of the blade.
3. Loosen the locking knob on the Grinding Angle Set-Up Jig and adjust the protractor so that
the black arrows are aligned with the correct grindstone diameter marking (Image E)
4. Then set the pointer to the required bevel angle on the blade (as measured in Step 2,
above) and tighten the locking collar to lock in position (Image E)
5. Thread the Straight Edge Jig onto the support arm so that the blade rests against the
grindstone
6. Position the curved foot of the Grinding Angle Set-Up Jig on the grindstone and the flat
section of the pointer on the blade to be sharpened (Image F)
7. Use the Support Arm Height Adjuster (12) to adjust the height of the support arm until the
flat section on Grinding Angle Set-Up Jig pointer lies perfectly flat on the
Operation
Important safety notes:
Never use this unit without wearing all necessary safety equipment, including approved
safety glasses and face or dust mask
Wear cut-resistant gloves and handle blades with care at all times
DO NOT test the sharpness of a blade on your finger (or other part of the body)
The grindstone and honing wheel rotate in the direction as marked by the arrow on the top
of the unit, adjacent to the horizontal mounts
Ensure the water trough is correctly fitted and sufficiently filled with water before starting
work. Check the water level at regular intervals and top up as necessary. NEVER attempt
to sharpen a blade when the stone is dry; it may be dangerous to do so.
Ensure the grinding stone surface is even and accurately graded for the task at hand
Check that the grindstone rotates freely each time before start up
Always allow a new wheel to run for a minutes before using it. Stand to one side at start
up
Switching on and off
1. Ensure On/Off Switch (4) is in the OFF (O) position
2. Connect the unit to the power supply
3. To switch on, press the on/off switch to ON position (I)
4. To switch off, press the on/off switch to OFF position (O)
5. Disconnect the device from the power supply if interrupted and when finishing work
Sharpening a blade
Apply blade to the grindstone with an even pressure
Slide the Straight Edge Jig back and forth along the support arm to ensure even grinding
on the blade and even wear on the stone
Do not press hard. Light pressure is all that is required for sharpening
Sharpening without the Straight Edge Jig
If the workpiece is too large to mount in the jig, you can fit the Support Arm (11) and rest
the workpiece on the support, with the edge pointing away from you. This will help you
keep the blade steady at the angle required
Move the blade back and forth across the stone to ensure even grinding on the blade and
even wear on the stone
Note: A Support Arm Extension (TWSSAE) and several tool specific jigs, such as the Long Knife
Jig (TWSLKJ) are available from your Triton stockist (see optional extras for more information).
It is highly recommended to always use a suitable tool specific jig when sharpening with
this device.
Honing a blade
After sharpening, using the leather honing wheel will remove any burr and give a smooth
sharp edge to the blade
WARNING: Always hone a blade in the direction of wheel rotation. NEVER hone against the
direction of the wheel .
1. Ensure the machine is disconnected from power during set up
2. Set up the Support Arm (11) and jig as shown in Image C. Use the Grinding Angle Set-Up
Jig (17) to check the blade angle is correct
3. Apply a generous squeeze of Polishing Paste (15) directly to the Leather Honing Wheel (1).
Honing will distribute the compound across the wheel
4. Switch on the machine and move the blade across the face of the honing wheel, ensuring
that at least half of the width of the honing wheel is always in contact with the blade
5. Allow the honing wheel to do the work. Do not apply excessive force to the wheel
6. As with sharpening, move the jig back and forth along the support arm to ensure even
honing of the blade
7. DO NOT hone without polishing paste on the wheel. If honing a number of blades, it may
be necessary to apply more paste. Switch off machine and remove blade before applying
compound
Honing without the Straight Edge Jig
If the workpiece is too large to mount in the jig, you can fit the Support Arm (11) and rest
the workpiece on the support, with the edge pointing away from you. This will help you
keep the blade steady at the angle required
Move the blade back and forth across the wheel to ensure even polishing across the blade
Removing engineering marks
The manufacturing process sometimes leaves blades with engineering marks on the
surface of the cross section (or ‘face’) of the blade
You can remove these by applying the damaged face of the blade to the side face of the
stone
Move the face of the blade slowly over the face of the stone. Do not apply excessive force,
and avoid fingers coming into contact with the stone
Carry out this procedure first, before you sharpen the blade
Finishing work
1. Disengage the drive system by loosening the Torque Adjustment Knob (10) This will help to
ensure the drive wheel retains perfect shape
2. Empty the water trough
WARNING: NEVER leave the grindstone standing in water.
949257_Z1MANPRO2.indd 7 16/03/2016 16:53
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Triton TWSS10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Triton TWSS10 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks als bijlage per email.

De handleiding is 19,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info