665091
9
Verklein
Vergroot
Pagina terug
1/134
Pagina verder
9
GB
Grinding Angle Set-Up Jig (TWSGAJ)
For setting up the correct angle for sharpening. Enables repeated accurate grinding of specific
bevel angles. (For usage instructions, see ‘Using the Grinding Angle Set-Up Jig’.)
Scissors Jig (TWSSJ)
2 1
5 4
3
Restores sharp edges to blunt scissors and garden shears. Twin clamps for securing blades.
Scissors Jig Familiarisation
1. Jig Support Plate
2. Scissor Clamp Holder
3. Scissor Clamp
4. Clamp Thickness Screw
5. Jig Tightening Knob
Using the Scissors Jig:
The Scissor Clamp Holder (2) is fitted with 2 Scissor Clamps (3). Normally, only the Scissor
Clamp on the right is required; however, for large scissors or shears the other clamp can
also be used
Adjust the Scissor Clamp/s to fit the scissor blade thickness. Loosen the Jig Tightening
Knob (5) then the Clamp Thickness Screw (4). Insert the scissor blade and re-tighten
The Jig Support Plate has a surface designed to allow the jig to move easily while
sharpening
IMPORTANT: DO NOT use the Leather Honing Wheel to remove the burr from the scissor blade
after using the Grindstone. To remove the burr, draw the scissor blade through the grain at the
end of a piece of wood.
Note: Portable electric-planer blades (not tungsten carbide blades) are ground in the same way
as scissor blades; however, honing using the Leather Honing Wheel is required.
Setting the bevel edge angle
The scissors’ bevel edge angle is set by adjusting the Jig Support Plate. Either repeat the
existing angle or create a new bevel edge angle by using the Grinding Angle Set-Up Jig
The same bevel edge angle:
1. Slide the Jig Support Plate (1) onto the Support Arm and tighten
2. Use a black marker pen to colour the bevel edge of scissor blade; rest the jig on the Jig
Support Plate with the scissors’ bevel edge touching the grinding wheel; and, using your
hand, turn the grinding wheel a quarter turn
3. Check the bevel edge to see what part of the black pen mark has been scratched off, then
adjust the Jig Support Plate to correct the angle
4. Re-test the quarter-turn scratch and re-adjust the Jig Support Plate if required
A new bevel edge angle:
1. Slide the Jig Support Plate onto the Support Arm and tighten
2. Use the Grinding Angle Set-Up Jig to set-up the Scissor Jig at the new angle (see ‘Using the
Grinding Angle Set-Up Jig’)
Support Arm Extension (TWSSAE)
Attaches to support arm. Provides simultaneous tool support above the grindstone and honing
wheels.
Carving Tool Jig (TWSCTJ)
For accurate sharpening of carving tools and other short tools. Clamps narrow and butt chisels
firmly. Internal ‘V’ shape automatically centres the tool.
Using the Carving Tool Jig:
1. Loosen the knob on the clamp and insert the appropriate chisel
2. Tighten the clamp’s knob
3. Use the Grinding Angle Set-Up Jig (see ‘Using the Grinding Angle Set-Up Jig’) and Support
Arm distance from the Grindstone to set the existing bevel edge grinding angle or a new
angle, if desired
4. Run the Whetstone Sharpener and frequently check the grind until the desired edge is
achieved
5. After grinding, use the Leather Honing Wheel and the Profiled Leather Honing Wheel
(TWSLHW optional accessory. See ‘Profiled Leather Honing Wheel’ for more information)
Note: Use the Stone Grader (see ‘Using the Stone Grader’) to change between rough or fine
grading of the Grindstone, depending on how much grinding and sharpening is required.
Note: You may need use the Leather Honing Wheel to remove the burr frequently during the
grinding process so that the progress of the sharpening operation can be seen clearly.
IMPORTANT: You must use the same angle on the Leather Honing Wheel that was used on
the Grindstone. Adjust the Support Arm to set the same angle. Use a black marker pen to see
where the leather makes contact with the carving tool by colouring in the bevel edge and
moving the Leather Honing Wheel in the correct direction by hand for a couple of rotations.
Check where the marker has worn away then adjust the Support Arm accordingly.
Note: The Support Arm Extension (TWSSAE) is ideal for use with the Carving Tool Jig because
there is no need to change the Support Arm. Access to the Grindstone and the Leather Honing
Wheel is at same time with the Support Arm Extension (see ‘Support Arm Extension’ in
‘Accessories’ for more information).
949257_Z1MANPRO2.indd 9 16/03/2016 16:53
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Triton TWSS10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Triton TWSS10 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks als bijlage per email.

De handleiding is 19,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info