607247
7
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Page.7
5. Positioning of ornamental log set (see page 11)
Position the ornamental log set exactly as shown in the illustration. Place the holes in the back logs of the set
over the pins in the bearing edge (back of combustion chamber) and subsequently lay the 2 rectangular logs
on the burner. Now position the remaining logs as shown in the illustration.
6. Fitting of glass window
Hang the glass window in the hinges. Close it and attach again with the two screws.
7. Fitting of the front to the combustion chamber /built-in casing
Place the front in front of the fireplace and attach it with the 4 screws: 2 at the top and 2 at the bottom behind
the service door.
6. DISMANTLING OF BURNER UNIT HV/LV AND FAN (HV only)
The burner unit and fan of a built-in appliance can be dismantled (the fan in the HV model only) without
having to take out the whole appliance.
This is done as follows:
1. Pull the fan plug out of the socket! (only in HV model)
2. Remove the screws with which the front is mounted (2 at the top and 2 at the bottom behind the service
door).
3. Loosen the screws with which the glass window is fixed and open the window.
4. Take the ornamental log set and the burner out of the fireplace.
5. Disconnect the two cable connectors for the outlet safety (on the left in the burner unit) and draw the
wire outside.
6. Close the main stopcock in the supply pipe and disconnect the burner unit from the pipe.
7. Pull the burner unit forward (be careful with the thermostat sensor).
8. Repair of the T.T.B. can be carried out in this phase, if required.
Dismantling fan system (HV model only).
In order to take out the fan, you must remove 3 screws at the back of the burner unit. The fan thermostat is
fixed with 2 screws to the partition at the right back of the burner.
Assembly is done in reverse order.
7. DISMANTLING OF T.T.B. BRACKET (see page 9 fig. 3)
Remove the two nuts and then take the T.T.B. bracket (3) out of the appliance with a turning motion, as
shown in figure 3.
8. LIST OF PARTS
1 Casing 10 Burner tray (HV) with burner H.V.
1A Knockout plates 11 Burner tray (LV) with burner L.V.
2 Heat exchanger 12 Pilot light burner
3 T.T.B. bracket 13 Sealing cap 3/8” and 3/8” gas connection
4 T.T.B. 14 Gas connection 3/8”
5 Combustion chamber 15 Fan switch high/low (HV)
6 Wood fender 16 Fan thermostat (HV)
7 Inside window 17 Front
8 Window
9 Door
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermocet VERSA LV-HV bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermocet VERSA LV-HV in de taal/talen: Engels als bijlage per email.

De handleiding is 0,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info